Milwaukee Angle Grinder Power Cords

Fix Number

FIX10131782

Manufacturer Part Number

44-76-0210

This cord protector is created to slide onto your cord and fit tightly at the end to protect the base of the cord from getting damaged. If the wires are exposed it can a be a safety hazard, so make sure to replace your cord protector if damaged. Refer to the manual provided by the manufacturer for further installation instructions.

Fix Number

FIX10122674

Manufacturer Part Number

22-64-0215

This is a cord set for your power tools. It is constructed with a tough outer-rubber insulation for a longer life span. The 18-gauge power cord is 8 feet long, and comes with 2 prongs and 2 wires. This cord is black in color and is sold individually.

Fix Number

FIX10122740

Manufacturer Part Number

22-64-0840

This cord is a genuine Milwaukee replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation and a cord protector for a long service life.

Fix Number

FIX10122833

Manufacturer Part Number

22-64-3430

This is a Genuine Manufacturer Approved replacement part designed for some Milwaukee Power Tools. This item is sold individually. Due to the use or other factors a cord can crack or get damaged otherwise. It is important to replace a damaged cord before continuing to use a Power Tool. Please note Cord Protector/Sleeve is Sold Separately.

Fix Number

FIX10131757

Manufacturer Part Number

44-76-0050

This is a Genuine OEM replacement Protector Grommet which is used on Milwaukee Power Tools. This part is made out of Rubber and is Sold Individually. It is important to have a cord protector on your tool to improve friction, seal cable and protect it from a potential damage. Replacing this item would differ based on your tool. • First you would need to gain access to internal connections of Power Cord by removing housing of your tool • Once you have disconnected Power Cord you would need to loop it through the Protector • Re-Connect Power Cord to your tool • Secure Cord Protector in the Housing opening and assemble your tool

Fix Number

FIX10122793

Manufacturer Part Number

22-64-2021

Fix Number

FIX10131765

Manufacturer Part Number

44-76-0095

This piece is a genuine replacement part made by the original manufacturer. It is compatible with Milwaukee angle grinders. Located at the connection point between the power cord and the machine, it protects the cord from strain and damage. Damaged cords should be replaced. This item is sold individually. Replacement cords are sold separately. • Disconnect tool from power source • Remove the outer case • Disconnect cord/wires from tool • Pull cord through the cord protector • Reconnect wires • Reassemble and test out tool

Fix Number

FIX10131774

Manufacturer Part Number

44-76-0130

This is an authentic and original replacement part. It fits a variety of Milwaukee handheld power tools. This cord protector prevents strain/damage to the cord where it connects to the tool. One (1) rubber cord protector is included in this purchase. Please note that a replacement cord is sold separately. Depending on your power tool model, a screwdriver should be the only tool needed to complete this repair. • Ensure tool is disconnected from power source • Remove the tool casing • Disconnect cord/wires from tool • Pull cord through the cord protector • Reconnect wires • Reassemble and test out tool

Fix Number

FIX10131780

Manufacturer Part Number

44-76-0170

This is a genuine OEM sourced replacement part that is used with Milwaukee grinders and sanders. Its job is to protect the power cord from over-bending and kinking. Because it is made of rubber, the cord guard will eventually become brittle and begin to crack. Please note this high quality rubber cord protector is sold individually.

Fix Number

FIX10122792

Manufacturer Part Number

22-64-2020

This is a genuine manufacturer sourced replacement part designed for Milwaukee grinders. If the cord is damaged it is important to replace it before continuing to use the tool. This cord is sold individually. Please note cord protector/sleeve is sold separately. To complete this repair you would need a screwdriver.