Power Motor Parts

Carbon Brush Set

$33.18

Fix Number: FIX10097316
Manufacturer Part Number: 44815

Genuine Ridgid replacement part Set of 2 Carbon Brushes with wire lead and brush spring attached. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Brush Cap Set

$13.83

Fix Number: FIX10097420
Manufacturer Part Number: 45660

This is an authentic manufacturer approved replacement brush caps. They are specially designed for Ridgid power drives. Brush caps are used to secure the brush in the tool. These caps have external threads that to screw into the opening on the housing of the tool. Be careful when removing and replacing these, they have a tendency to break. This item is made out of plastic and it is sold individually. You would need a flathead screwdriver to install or remove these caps.

1/4\\\\\\\\\\\\\\\ Collet

$66.82

Fix Number: FIX10335906
Manufacturer Part Number: 308PT

This is an authentic replacement collet which is supplied directly from the original equipment manufacturer for use with Cleco and Dotco. This part allows a user to secure a router bit, keep in mind it is for use with 1/4" arbors only. It is made of high-quality metal and is sold individually, please note the collet nut is sold separately.

Grinder Grinder/Sander Rotor Blade

$15.72

Fix Number: FIX12145308
Manufacturer Part Number: 1906PT

This part is sourced directly from Dotco and is designed to work with various Dotco and Cleco Grinders and Sanders. For full compatibility, please see the "Model Cross Reference List" below. The Rotor Blade is responsible for producing airflow inside the cylinder. If your tool has less power than before, it may be a sign that you have damaged Rotor Blades. If your Rotor Blades are cracked, chipped, or damaged, your tool will not operate properly, and they need to be replaced. Each blade is approximately 1" long, and are sold individually.

F-532 Grommet (5)

$19.87

★★★★★

1 Review

Fix Number: FIX10096810
Manufacturer Part Number: 40940

This is a genuine OEM replacement part that has been sourced directly from Rigid. These grommets, also known as rubber feet, are commonly used on pipe tools, and tool stands. Grommets help keep your equipment in one place, they also help keep it balances, and they help reduce vibration during operation. To install this replacement part you simply push the grommet into the pre-drilled hole and the bottom of your equipment. These rubber feet come in a pack of five.

Rotor Blade

$18.45

Fix Number: FIX10303495
Manufacturer Part Number: 2253PT

This authentic manufacturer approved replacement rotor blade is designed for use with Cleco and Dotco power tools. It fits in the rotor helping to push the air inside the tool. Depending on your equipment you may need more than one (1) of these blades. This part is made out of composite material and it is sold individually.

Jaw Insert Set

$165.00

Fix Number: FIX10097301
Manufacturer Part Number: 44715

This jaw insert set is sourced from the original manufacturer for use in pipe and bolt machines. The set includes 3 jaw inserts, 3 pins used to attach the inserts to the jaws and 3 springs to provide the tension for the jaws to open and close. These components work together to grip the pipe or bolt securely and prevent it from rotating or moving while the threading dies cut the threads. Over time the components may wear down, corrode, or become damaged leading to loss of control, instability, weak grip, and overall lower efficiency. Disconnect the machine from power and remove the equipment housing. Locate the cap and remove the jaw insert, pin, and spring. Clear the area of any old metal shavings and debris. Position the new spring and pin in place. Attach the new jaw insert and ensure it is securely held in place. Reassemble the equipment to complete the repair.

Power Cord (8-foot)

$78.52

Fix Number: FIX10103727
Manufacturer Part Number: 89155

This is a genuine service cord made for Ridgid power driver/cutting tools. It is supplied directly from original equipment manufacturer and it is sold individually. If the cord is damaged it is important to replace it before continuing to use the tool. Please note, the cord protector/sleeve is not included with this service cord, it is sold separately. To complete this repair you would need a screwdriver. • Remove the housing • Disconnect wires • Remove old cord • Secure the new one in place • Reconnect wires • Reassemble and test the tool

Power Cord Retainer

$8.73

Fix Number: FIX10097508
Manufacturer Part Number: 46730

2 Brush Holders

$72.87

Fix Number: FIX10097313
Manufacturer Part Number: 44795

This item is sold as a set of two which are made of metal. The brush holder goes between the brush assembly and the field housing assembly. A wrench may be helpful when replacing this part. It may become broken and will need to be replaced. This part is a Ridgid replacement part directly sourced from the manufacturer for use in power drives.

Popular Power Motor Parts

Power Motor Brands

Related Power Motor Parts

Popular Power Motor Models

Power Motor Parts

Start With Your Model Number

Popular Power Motor Parts

Power Motor Brands

Related Power Motor Parts

Popular Power Motor Models