OEM Ryobi Snow Blower Parts & Accessories

FAN

$6.51

Fix Number: FIX18786062
Manufacturer Part Number: 537642001

Washer-lock 5/16

$6.69

Fix Number: FIX9311087
Manufacturer Part Number: 936-0119

This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with the following snowblowers: Lawn tractor, tiller, chipper, shredder, lawn mower, snow blower, leaf blower/vacuum, log splitter, edger, hedge trimmer, and engine. Refer to the manual provided by the manufacturer for repair instructions.

Snow Blower Hex Flange Bearing

$14.16

Fix Number: FIX9178250
Manufacturer Part Number: 941-0245

Shoe-slide

$37.57

Fix Number: FIX9135084
Manufacturer Part Number: 784-5580-0637

This slide or skid shoe fits snow blowers and is attached to the auger housing. The shoe slides around the ground to ensure the snow blower glides and moves easily. It also elevates the auger housing to protect it from damage. *Please note: this part is sold individually. It is recommended both skid shoes are replaced to prevent unevenness. Refer to the diagram provided by the manufacturer for further installation instructions and safety practices.

Bushing-.380 Id

$6.51

Fix Number: FIX9167515
Manufacturer Part Number: 941-0475

This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventually wear out. When that happens, you must replace it. Before making this repair, we recommend letting your machine cool, and draining the gas tank.

Cable-clutch X 39.

$40.52

Fix Number: FIX9170572
Manufacturer Part Number: 946-0898

This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the control handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable

Fixes these symptoms

Drive system does not work
See more...

Installation Instructions

Leonard from South Hadley, MA

Drive would Slip in and out then unable to engage traction control.

Removed frame cover. Found broken Idler Spring. This is what cause the slipping and clunking noise. also check or replaced as I did.t The Extension Spring is a little harder to get to. With the idler spring broken this cause the friction wheel and support bracket to break the Drive Clutch Cable Spring and Support Bracket Spring. Easy to replace. At this time clean and oil the part called 7-tooth shaft. This helped shifting speeds. Be careful not to get any oil on the friction wheel or the friction disc. FYI Problems like this will always happen at the wrong time. The web site easy to use but the illustrations and part numbers could be better to read. Need to have clearer zoom and part number to part. Not sure part name like spring-extension or extension-spring. So I purchased both parts. This snow blower easy to use and repair. A simple design. Read more...

Shear Bolt (5/16-18 X 1.5'' Lg.)

$6.51

Fix Number: FIX9100904
Manufacturer Part Number: 710-0890A

This replacement shear bolt is supplied directly from the original equipment manufacturer for use with Craftsman snowblowers. The purpose of this hardware is to protect your snowblower. If the auger gets jammed or clogged, the shear bolt is designed to snap at a certain point of pressure, that way it will not damage any other part of the unit. Please note this high-quality component is made of durable metal and is sold individually.

Snow Blower Worm Gear

$62.65

Fix Number: FIX9165943
Manufacturer Part Number: 917-04861

Carriage Bolt 5/16-18 x 3/4" Lg.

$6.51

Fix Number: FIX9298671
Manufacturer Part Number: 710-0451

This carriage bolt fits a variety of tools and is sold individually. The square area under the head of the bolt is created to fit into a square hole in your tool. The hole makes sure to restrain the bolt and prevents it from turning when the nut is secured or tightened.

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...

Snow Blower Auger Clutch Cable

$32.78

Fix Number: FIX9170571
Manufacturer Part Number: 946-0897

Fixes these symptoms

Auger will not turn
See more...

Ryobi Snow Blower Parts

Popular Ryobi Snow Blower Parts

Installation Instructions

Installation Instructions

Ryobi Snow Blower Appliance Types

Related Ryobi Snow Blower Parts

Popular Ryobi Snow Blower Models

Ryobi Snow Blower Parts

Start With Your Model Number

Popular Ryobi Snow Blower Parts

Installation Instructions

Installation Instructions

Ryobi Snow Blower Appliance Types

Related Ryobi Snow Blower Parts

Popular Ryobi Snow Blower Models