Snapper Lawn Tractor Belts

Fix Number

FIX18606736

Manufacturer Part Number

7043844YP

The drive belt wraps around the spindle pulley and is available as an individual replacement part. This is an original Snapper part designed for rear engine rider mowers. The belt will need to be replaced if it becomes stretched or broken. During installation, a wrench may be needed to replace this item.

Fix Number

FIX16298804

Manufacturer Part Number

1728008SM

This is a genuine manufacturer-sourced replacement v-belt which is specially designed for use on Murray, Snapper and Simplicity lawn and garden equipment. It is the main belt which drives the unit, over time it may wear out or stretch eventually requiring a replacement. Clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. This high-quality part is made of durable rubber material and it is sold individually.

Fix Number

FIX9072068

Manufacturer Part Number

7022252YP

Spindle belt. Width: 1/2 " Length: 73 1/2 "

Fix Number

FIX18586617

Manufacturer Part Number

1601672SM

This part is an OEM Snapper part for use with Lawn Tractors. The drive belt connects the engine crankshaft pulley to the transmission pulley. The most common reason for replacing the drive belt is when the lawn mower wheels won't turn. This part is sold individually. The tools that you will need to replace the drive belt is a 5/8 inch socket and a pipe wrench.

Fix Number

FIX8892237

Manufacturer Part Number

1732955SM

This is an authentic manufacturer sourced replacement v-belt which is specially designed for use with Murray, Snapper, and Simplicity lawn mowers. It is the main deck belt that is used to drive the blades, unfortunately, over time belts tend to wear out and stretch eventually requiring a replacement to maintain peak performance. Clean the pulleys before installing the new belt to ensure top performance and longevity with your new belt. Keep in mind this high-quality part is made of durable rubber and is sold individually.

Fix Number

FIX16298228

Manufacturer Part Number

1719911SM

This is an authentic Snapper replacement part. The V-belt is commonly found in lawn mowers. This part is made of flexible rubber with a tight fabric casing. It is used to turn the pulleys, transferring power from the motor to the mower blades. Over time, this part can become cracked and brittle, and need replacement. You may require a screwdriver or wrench when replacing this part. This item is sold individually.

Fix Number

FIX18594375

Manufacturer Part Number

5023255SM

Belt #7-8055 155 e.l

Fix Number

FIX12089861

Manufacturer Part Number

37X66MA

This is a Genuine Manufacturer Approved replacement Belt used on Murray Lawn Tractors. This part is made out of Rubber and it is Sold Individually. This is the the Smaller Belt that drives Blades on your unit. Clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Fist you would need to lower the mower deck to the lowest position • Then move the blade engagement lever to the Off position. • Roll the belt off the engine pulley from between the belt guide and pulley. • Remove mower deck by removing the bow-tie pins securing the left and right lift arms • Disconnect the blade engagement cable from the mower deck • Remove the bolts from the mower deck belt pulley covers and pull the covers off. • Loosen but don't remove the nuts on the top of the idler pulleys. • Install the new mower deck belt through the belt guides and around the pulleys. • Tighten the nuts on the top of the idler pulleys. • Re-Assemble the Deck

Fix Number

FIX18587420

Manufacturer Part Number

1703836SM

This is a genuine replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The belt is used to link the arbor pulleys on the mower deck to drive the mower's blades. It is recommended to clean the pulleys when installing the belt to avoid damage to the new belt. This item is sold individually.

Fix Number

FIX9091625

Manufacturer Part Number

7100102SM

V-belt hydro drive