OEM MTD Lawn Tractor Accessories Parts & Accessories

$2.99

Bow Tie Cotter Pin

Fix Number FIX9096195

Manufacturer Part Number 714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

$3.48

Nut, Flange Lock, 5/16-18, Grf

Fix Number FIX9092936

Manufacturer Part Number 712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...

$3.59

Nut, Flange Lock, 3/8-16, Grf

Fix Number FIX9095080

Manufacturer Part Number 712-04065

This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of the bolt hole is 3/8 inches and the thread count is 16. For instructions on where the lock nut is located in your tool refer to the manual provided by the manufacturer.

$3.82

Nut, Flange Lock, 1/4-20, Grf

Fix Number FIX9299574

Manufacturer Part Number 712-04064

This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torque type lock nut, and it has no temperature or chemical restrictions. This part has a 1/4-inch diameter and 20 thread size.

$2.99

Shear Pin, .25

Fix Number FIX9110822

Manufacturer Part Number 738-04124A

Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.

$4.20

Washer-Lock 5/16

Fix Number FIX9311087

Manufacturer Part Number 936-0119

This lock washer is used to resist the loosening of bolted joints. Repair tip: It is difficult to install the lock washer in a tight place or when the bolt/screw is pointing down. This lock works with the following appliances: Lawn tractor, tiller, chipper, shredder, lawn mower, snow blower, leaf blower/vacuum, log splitter, edger, hedge trimmer, and engine. Refer to the manual provided by the manufacturer for repair instructions.

$3.65

Plastic Bushing .380 ID

Fix Number FIX9167515

Manufacturer Part Number 941-0475

This is a plastic bushing for your lawn equipment. It fits onto the side of your fuel tank, and holds the fuel fittings so they do not touch sharp metal. This part is made of plastic, and will eventually wear out. When that happens, you must replace it. Before making this repair, we recommend letting your machine cool, and draining the gas tank.