OEM Yard Man Lawn Mower Parts & Accessories

Bow Tie Cotter Pin

$3.99

Fix Number: FIX9096195
Manufacturer Part Number: 714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

Nut, Flange Lock, 5/16-18, Grf

$5.95

Fix Number: FIX9092936
Manufacturer Part Number: 712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...

Watch the install video

Mulching Blade

$29.79

Fix Number: FIX9169783
Manufacturer Part Number: 942-0741A

This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces along the edges of the blade. If installed correctly this part will keep the grass clipping under the deck longer, and re-cut them. The blade is 21 inches long, and sold individually.

Fixes these symptoms

Mower blade does not cut
See more...

Fuel Bowl O-Ring

$7.68

Fix Number: FIX17016670
Manufacturer Part Number: 951-11589A

Fuel Bowl O-Ring

Element, Air Cleaner (Wix Filters)

$10.17

Fix Number: FIX12127252
Manufacturer Part Number: 17211-Z8B-901

This part includes one OEM quality air cleaner for a small engine. A clogged air cleaner will stop air flow to the carburetor, resulting in poor engine performance. The air filter should be checked before operating it, each and every time. Operating an engine without an air filter or with a damaged or clogged one, will allow debris to get to the engine and this cause serious and expensive damage to the engine. For this simple replacement, no tools are needed. Press the retaining tabs down and this will release the cover. With the cover removed, pull the old air cleaner off by hand. Install the new air cleaner by placing it in the housing and aligning the lower cover tabs with the housing and then snap the upper tabs into place.

Variable-Speed Belt

$53.72

★★★★★

1 Review

Fix Number: FIX9186148
Manufacturer Part Number: 954-0467A

This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit. Make sure to clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Loosen the transaxle pulley • Relieve tension on the upper drive belt • Remove the upper drive belt and lawn mower belt guide • Secure the new belt • Reassemble and tighten the pulleys

Nut, Flange Lock, 3/8-16, Grf

$5.95

Fix Number: FIX9095080
Manufacturer Part Number: 712-04065

This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of the bolt hole is 3/8 inches and the thread count is 16. For instructions on where the lock nut is located in your tool refer to the manual provided by the manufacturer.

Watch the install video

Bell Blade Support

$6.15

Fix Number: FIX17016260
Manufacturer Part Number: 736-0524B-1

This is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made of metal to ensure a long life. If there is visible damage or wear, replace this part.

Installation Instructions

Michael from Lillian, AL

Blade became warped over time, baffle was falling down

In order to change the blade in a push mower you need to use a 2x4 or equivalent to stop the blade from spinning. I bent the blade back previously by heating it up but I think it was causing too much vibration so I got a new blade after hitting stumps over the years. I run some things into the ground. The spark plug is amazing and really high quality. Its a simple change. The drive belt is also a simple change, any 6 in 1 if you remove the screw heads will have the right nut sizes for most mower parts. Always lube up the belt "like two drops" with a little belt oil and it will last longer. I use diesel oil, 3 n 1, or chain saw bar lube oil. The tensioner for the belt is an easy adjustment. This model is also prone to fuel lines being blocked. Just detach the fuel line, blow it out with your mouth, and reattach. Have had it happen twice in 10 years, some people would be pulling spark plugs, diagnosing the engine, etc, its pretty easy, just put some fuel on the carb to see if your getting fuel blockage. Read more...

Nut, Flange Lock, 1/4-20, Grf

$5.95

Fix Number: FIX9299574
Manufacturer Part Number: 712-04064

This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torque type lock nut, and it has no temperature or chemical restrictions. This part has a 1/4-inch diameter and 20 thread size.

V-Belt

$53.72

Fix Number: FIX11813755
Manufacturer Part Number: 954-04060C

This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Yard Man Lawn Mower Parts

Popular Yard Man Lawn Mower Parts

Installation Instructions

Installation Instructions

Yard Man Lawn Mower Appliance Types

Popular Yard Man Lawn Mower Models

Yard Man Lawn Mower Parts

Start With Your Model Number

Popular Yard Man Lawn Mower Parts

Installation Instructions

Installation Instructions

Yard Man Lawn Mower Appliance Types

Popular Yard Man Lawn Mower Models