KitchenAid Ice Maker Ice Cutting Grid Wire 4387020 | Fix.com

Ice Cutting Grid Wire

&SeePartX&
370853-1-S-Whirlpool-4387020           -Ice Cutting Grid Wire
370853-2-S-Whirlpool-4387020           -Ice Cutting Grid Wire
https://fixcom.azureedge.net/Schematics/Maytag/03FL2TOQ.gif
Click for the BBB Business Review of this Appliances - Small - Supplies & Parts in Dartmouth NS
Part Description:
There is approximately 10'of wire. Note:2 kits are needed to replace both directions.
This part works with the following brands:
Part number cross reference:
This part works with the following products:
Ice Maker, Refrigerator.

Installation Instructions

Showing 1-3 of 3 Instructions

One of the wires on the isce cutting grid was broken.

My husband repaired it. It took him less than ten minutes. He said it was very easy and not time consuming at all. Will not be hesitant to order from you again.

Were these instructions helpful?

1 of 1 people found these instructions helpful
Parts Used: Ice Cutting Grid Wire
Difficulty Level: Really Easy
Total Repair Time: Less than 15 mins
Tools:
Customer: Maria from Barberton, OH

Replacing cutting grid wire

Removal of the cutting grid assembly is very easy. 2 1/4 inch screws to remove on each side, then disconnect the wiring from the plugs on each side and lift out. There is a screw on each end of the wire holding it down. Simply loosen those to take the old wire off. Start at one end by wrapping around the first screw and tighten the screw down to hold in place. Then begin wrapping the wire from end to end. I used needle nose pliers to keep it as rigid and tight as possible. I also used my fingers to straighten while I pulled tight. Then wrap the other end around the second screw and you are done. Worked like new.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Ice Cutting Grid Wire
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Dennis from Shawnee, KS

Ice cutting grid wire broke

This is a fairly easy repair. The challenge is keeping the new wire taut to eliminate kinks and create a uniform wire grid. I have a recent model, and my grid cutter doesn't have wire tension-adjustment screws. I couldn't pull the wire tight enough by hand, and I didn't want to risk damaging the wire by using pliers to grip it. Instead I used a small piece of 1-1/2 inch pvc pipe to coil the new wire and then feed it out slowly around the cutter guides. I pulled on the pipe to keep the wire taut. I had a helper hold the cutting grid while I looped the wire around each guide. It only took a few minutes to attach the new wire. The results were excellent.

Were these instructions helpful?

0 of 1 people found these instructions helpful
Parts Used: Ice Cutting Grid Wire
Difficulty Level: Easy
Total Repair Time: 30 - 60 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Michael from Overland Park, KS
Showing 1-3 of 3 Instructions

Model Cross Reference List

This part works with the following models:

Fix Number: FIX370853
Manufacturer Part Number: 4387020


Brand Model Number Description
Kenmore1064689482991Ice Maker
Kenmore10686482690Ice Maker
Kenmore10686482691Ice Maker
Kenmore10686485690Ice Maker
Kenmore10686485691Ice Maker
Kenmore10689482990Ice Maker
Kenmore10689482991Ice Maker
Kenmore10689482992Ice Maker
Kenmore10689482993Ice Maker
Kenmore10689482994Ice Maker
Kenmore10689482995Ice Maker
Kenmore10689482996Ice Maker
Kenmore10689482998Ice Maker - ICE MAKER FREE STANDING
Kenmore10689483700Ice Maker - ICE MAKER FREE STANDING
Kenmore10689483992Ice Maker
Kenmore10689483993Ice Maker
Kenmore10689483994Ice Maker
Kenmore10689483995Ice Maker
Kenmore10689483996Ice Maker
Kenmore10689483998Ice Maker - ICE MAKER FREE STANDING
Kenmore10689485990Ice Maker
Kenmore10689485991Ice Maker
Kenmore10689485992Ice Maker
Kenmore10689489700Ice Maker - ICE MAKER FREE STANDING
Kenmore10689489990Ice Maker
Kenmore10689489991Ice Maker
Kenmore10689489992Ice Maker
Kenmore10689489993Ice Maker
Kenmore10689489994Ice Maker
Kenmore10689489995Ice Maker