Dynabrade Parts

Fix Number

FIX10340124

Manufacturer Part Number

95218

This knob is an original part from Dynabrade and is used as a securing mechanism in the equipment listed below. This part consists of a plastic knob with a metal threaded shaft. Please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. This item is sold individually.

Fix Number

FIX12023329

Manufacturer Part Number

11011

This is a Genuine OEM sourced replacement part designed for Dynabrade Dynafile. This Idler Wheel helps to support and drive the Sanding Belt. It is made out of Metal and it is Sold Individually. This assembly includes the Wheel, Bearing and a Bolt that secures it.

Fix Number

FIX10337784

Manufacturer Part Number

40750

It is an authentic manufacturer-sourced replacement set which is specially designed for use with Dynabrade power tools. The brushes play the key role by conducting electric current while maintaining physical contact with an armature. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem. This set includes two high-quality carbon brushes with attached lead wires.

Fix Number

FIX10338983

Manufacturer Part Number

57113

This is a genuine Dynabrade replacement part designed for use with sanders/buffers. It fits inside the cylinder assembly. This set includes a plastic rotor and a set of five (5) blades. To replace it you will need a screwdriver and pliers.

Fix Number

FIX10336584

Manufacturer Part Number

01480

These authentic OEM sourced replacement rotor blades are commonly used on Dynabrade sanders and grinders. They are attached to the rotor inside the tool pushing the air. This set includes (4) compound material blades per order. Replacing these blades you will need a set of wrenches and pliers.

Fix Number

FIX10336518

Manufacturer Part Number

01011

These blades in your die grinders are located on the rotor within the motor housing. This OEM set includes four blades, each measuring approximately 1-1/2 inches by 3/8 inches. When the tool is turned on, the motor drives the rotor, causing the blades to spin rapidly and help you shape various materials. It is important to regularly check the condition of the blades and replace them if they are visibly worn out or misaligned. Additionally, pay attention to any unusual signs during operation, such as increased noise, vibration, or burning smells. To replace the blades, refer to your user manual for detailed instructions on how to disassemble the motor housing. Typically, you will need to secure the tool in a padded vise, then use an adjustable pin wrench to remove the lock ring. Proceed with disassembling the tool by removing the collet and rotor nut from the rotor shaft, followed by the cylinder, spacer, and the four blades from the rotor.

Fix Number

FIX10336573

Manufacturer Part Number

01464

This is a manufacturer sourced replacement seal. It is specially produced for use with Dynabrade sanders. This is one of the seals for the tip valve/inlet bushing. Over time seals tend to shrink and crack allowing for air leaks. At that time it should be replaced to maintain top performance. It is made out of rubber material and it is sold individually. Replacing this item you would need a wrench to replace this item.

Fix Number

FIX12023348

Manufacturer Part Number

11218

This item is a genuine Dynabrade part that is OEM sourced to ensure quality. The contact arm assembly is intended to be used with belt sanders. The contact arm assembly attaches to the idler arm and is used as the turn at the end of the belt loop. The assembly includes the front roller and belt pads. This item is priced as a single item.

Fix Number

FIX10336574

Manufacturer Part Number

01468

This is a spring for your sander. It is known as a conical spring because it is cone shaped, and coiled. It is comparable to a compression spring because it stores energy by absorbing shock, and then releasing it, to maintain the force between two surfaces. The spring is a part of the muffler assembly in your sander. The muffler assembly reduces the noise coming from your machine. Over time the spring may lose tension and need replacing. If you are replacing your muffler assembly, or similar parts, we also recommend replacing the spring for an even wear.

Fix Number

FIX10339145

Manufacturer Part Number

57890

This is an authentic Dynabrade replacement part that has been sourced from the original manufacturer to be used with orbital sanders. The isolator post is used to provide spacing between the housing and the backing pad to allow room for the bearing box. This item is sold as an individual replacement part.