High Limit Thermostat
Works With Model EIMED55IIW0!
$86.82
In Stock
Fix Number: FIX446428
Manufacturer #: 3204267
Manufactured by:
Frigidaire
Works With Model EIMED55IIW0!
-
Product Description
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops by 70 degrees Fahrenheit.
-
Works with the following brandsFrigidaire, Kenmore, Electrolux, Gibson
-
Works with the following productsDryer, Washer Dryer Combo
-
Fixes the following symptomsToo hot
-
Part Number Cross ReferencePart# 3204267 replaces these:AP2131477, 508516, 73204267
Product Description
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops by 70 degrees Fahrenheit.
-
Works with the following brands:Frigidaire, Kenmore, Electrolux, Gibson
-
Works with the following products:Dryer, Washer Dryer Combo
-
Fixes the following symptoms:Too hot
-
Part# 3204267 replaces these:AP2131477, 508516, 73204267
Videos For installing this part.
Replacing your High Limit Thermostat

Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related PartsAdditional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:jason from CANTON, MS
-
Parts Used:3204267
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
dryer would turn off after 30 seconds
Disconnected dryer, from power, remove the back cover, replaced part, reassemble and tested
Was this instruction helpful to you?
Thank you for voting!
-
Customer:James from Palm Coast, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
No Heat and error on front panel after about 2 minutes after running
removed 2 rear screws, removed top panel. Removed 2 top screws and 2 internal screws, disconnected electrical connections and removed front panel. removed drum guide. Disconnected drive belt, removed drum. removed 4 screws from rear, removed the heating element assembly. Cleaned the entire bottom section of the dryer. Installed new heating element assembly, installed thermal limiter and control thermistor, reassembled the dryer. Dryer has been working great!
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Timothy from Boulder, CO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Dryer was not effectively drying clothes
I replaced the control thermistor and high limit thermistor. I followed the video and although it was a different model the dismantle and assembly instructions were very helpful. I did discover that the location for one of the sensor in the mechanical views provided was incorrect. I also discovered that the real problem was that the hot air venting was plugged and most likely the cause of the problem in the first place. I am not sure that this was listed as a cause of the problem but it was certainly where I should have started from.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX446428
Manufacturer Part Number: 3204267
Manufacturer Part Number: 3204267
Brand
Model Number
Description