Drum Support Bearing
Works With Model DEA501F1W!
$9.05
In Stock
Fix Number: FIX418807
Manufacturer #: 131825900
Manufactured by:
Frigidaire
Works With Model DEA501F1W!
-
Product Description
The drum support bearing is an authentic OEM replacement part for your dryer. The bearing is used to support the drum and allow it to rotate smoothly and quietly. If your dryer is excessively noisy while tumbling, will not start, will not tumble, or if it is leaving marks on your laundry, you may need to replace the drum support bearing. The bearing is found on the inside of the rear panel of the dryer cabinet, and you will need to remove the drum in order to complete this repair. Please be sure to disconnect the power supply to your dryer before you begin.
-
Works with the following brandsFrigidaire, Kenmore, Gibson, Westinghouse
-
Works with the following productsDryer, Washer Dryer Combo
-
Fixes the following symptomsNoisy, Marks left on clothes
-
Part Number Cross ReferencePart# 131825900 replaces these:AP2107679, 774936, 08015223, 3281008, 5303281008, 8015223, Q000143951, Q143951, WQ143951
Product Description
The drum support bearing is an authentic OEM replacement part for your dryer. The bearing is used to support the drum and allow it to rotate smoothly and quietly. If your dryer is excessively noisy while tumbling, will not start, will not tumble, or if it is leaving marks on your laundry, you may need to replace the drum support bearing. The bearing is found on the inside of the rear panel of the dryer cabinet, and you will need to remove the drum in order to complete this repair. Please be sure to disconnect the power supply to your dryer before you begin.
-
Works with the following brands:Frigidaire, Kenmore, Gibson, Westinghouse
-
Works with the following products:Dryer, Washer Dryer Combo
-
Fixes the following symptoms:Noisy, Marks left on clothes
-
Part# 131825900 replaces these:AP2107679, 774936, 08015223, 3281008, 5303281008, 8015223 ... Show more , Q000143951, Q143951, WQ143951 Show less
Videos For installing this part.
Replacing your Drum Support Bearing
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
April 10, 2022
Is there A vidio for installing FIX12579101 on this stacker model ??
thanks steve
For model number LCE752L-L2
Hello Steve, Thank you for your inquiry. Although we do not have a repair video for this exact part number, we do have a video for a similar bearing bracket to give you a general idea of the repair. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Related PartsAdditional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:michael from Cave City, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Donald from SPRINGVILLE, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
squeacky drum
remove control panel,unplug door switch connector,removedryer door assembly,unhook belt from tensioner,lift druum out of drum bearing and remove drum. change therear bearing,using bearing grease to retain the small ball bearing in the back of thedrum bearing during assembly. reverse for reassembly.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Gordon from Eau Claire, WI
-
Parts Used:131825900
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Dryer squeals when running
Followed video demonstration and it was easy. Used putty knife to release two latches under front edge of top cover. Tilted cover back against wall, removed two phillips screws at each inside location, lifted fron panel and swung aside to right location. Disengaged idler pulley and belt under drum (in lower corner) Used belt slack on top of drum to lift drum up and forward out of support bearing. Removed drum forward and out onto floor. Located drum support bearing in back/center of back panel held by two screws. Installed new bearing and reassembled. Runs great. Before this operation I had been almost ready to buy new dryer at $300 or more. Very satisfied with instructions and shipping service -- and minor cost !
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Michael from Milan, TN
-
Parts Used:131825900
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Squeeking
Followed instructions in video. Easy to understand.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Ronald from Clermont, FL
-
Parts Used:131825900
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Loud squeaking noise
Pull control panel off. Remove door. Remove front of dryer. Remove top cover. Take belt off. Remove the dryer drum. Remove and replace the drum support bearing. Reverse steps to put back together.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:todd from rogersville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
nosiy dryer
it went great
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Ben from Corrales, NM
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
thumping sound drum was wobbling
Replaced the drum bearing kit. Hardest part was screwing new screws into the rear bearing. I recommend you screw them in first then take them out then place bearing on drum and screw them back in or youll never bet them on. Add plenty of grease and put the bearing in from outside back not from inside. Alot easier. CAREFUL OF METAL SO SHARP IT CUTS LIKES RAZOR USE TOWEL AND LONG SLEEVES OR YOULL LOOSE FINGERS EASY.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Brent from Maple Grove, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
No heat, drum would spin
so eliminated idea of thermostat. replaced heating element coil. also replaced drum bearing and belt as long as it was apart Forgot to mention how quickly we received our parts. Amazingly fast. Thank you .
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Steven from Citrus Heights, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Dryer was making a squealing noise
On the back of the dryer there is an inspection cover, remove it and you can get to the belt. release tension and remove the belt (Very easy to do, no tools required). Two screws hold the top in place, remove, slide top back and set to side. There are two screws and four clips holding the front on remove the screws and pop the clips loose, unplug wiring harness and remove front. Remove plastic guide that is in front of the drum, pop drum up and out of bracket holding the back, slide drum out the front. Now you have access to the rear drum bearing. Reassemble in the reverse order. There is a good video online that you can follow prior to starting this project.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Jill from South Bristol, ME
-
Parts Used:131825900
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
Loud squeal while dryer was running
Same as the video, except we didn't dare to pull the belt to pop the drum out of the drum support bearing as it was looking old and we had only ordered the drum support bearing not a new belt too. We popped it out with a claw hammer (claw side) which worked fine. Also, we didn't have any hi temp grease as called for in the video. This should come standard with the bearing!
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX418807
Manufacturer Part Number: 131825900
Manufacturer Part Number: 131825900
Brand
Model Number
Description