Gibson Washer Parts

Gibson Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Gibson Washer Parts

$25.92
In Stock
Drive V-Belt
★★★★★
★★★★★
(2)
Fix Number FIX1146950
Manufacturer Part Number 134511600
If your washer drum is not spinning, there may be an issue with your drive belt. The drive belt wraps around the motor pulley and helps the basket to spin. Other signs there are issues with the belt is if there is a burning rubber smell, or the washer is noisy while spinning. The belt is subjected to wear and tear, and over time it may wear out. This is a genuine OEM part that is made of rubber.
Fixes these symptoms
  • Burning smell
  • Noisy
  • Pumps but will not spin
  • See more...
Installation Instructions
michael from Cave City, KY
browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple Read more...
$13.10
In Stock
Door Strike
★★★★★
★★★★★
(1)
Fix Number FIX890617
Manufacturer Part Number 131763310
Located on the door of front load washing machines, the Door Strike ensures that the door will lock by activating the switch, which in turn allows the appliance to run properly. If your washer door will not open or close, is leaking, or the machine will not start or spin, your door strike may be damaged and should be replaced. Regular wear and tear, or a misaligned door may cause the piece to break. This is an easy repair and requires a Phillips screwdriver. This genuine OEM part is made of white plastic, approximately 2 inches in length, and is held in place by 2 screws on the inside of the door. Simply unscrew and remove the old part, line up the placement of the new part using the notch, and tighten the screws back into place.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Howard from Santa Rosa, CA
door ajar alarm
myself and it was easy , as the diy video described on your website Read more...
$51.58
Special Order
Water Inlet Valve
Fix Number FIX815509
Manufacturer Part Number 134190200
This washing machine water inlet valve has two ports for water to enter.
Fixes these symptoms
Installation Instructions
Yvonne from East Greenbush, NY
Washer did not dispense cold water
lift the top of the washer and remove three hoses connected to the water valve. Disconnect both sets of wires on the water valve and remove the two screws holding it in place. Insert new water valve, screw into place, replace wires and hoses. Most difficult part of the process was removing the top hose because the ends of the clamp holding it in place were extremely small. Read more...
$120.51
In Stock
Front Load Washer Door Lock and Switch Assembly
★★★★★
★★★★★
(1)
Fix Number FIX12364048
Manufacturer Part Number 131763256
This door lock and switch assembly is an authentic OEM replacement part for your front load washing machine. The lock is used to prevent the door from opening while the machine is running, and the switch indicates that the door is closed, allowing the washer to begin its wash cycle. Attempting to open the washer door while it is still locked can cause damage to these parts. If your washer door will not open, close, or lock, you may need to replace the lock and switch. Please be sure to disconnect the power supply to your washer before beginning this repair.
Fixes these symptoms
  • Leaking
  • Lid or door will not open
  • Lid or door won’t close
  • See more...
Installation Instructions
Arthur from New Castle, DE
Door would not close/latch.
Removed door from washer. With door on flat surface all the screws are easily removed to replace striker & door hinge/ bushings. Pay attention to bushings position when removing so as to replace them in the same position. Video shows a guy pulling the door gasket off to replace the door lock & switch assembly. Skip that & remove the top cover from the washer. Only two screws in the back hold it on & it's a lot easier to reach inside & pull the switch up than fighting with the door gasket. With the new door hinge, door closes easier & more solid than when brand new. Easy fix. Read more...
$131.24
In Stock
Drain Pump - 120V 60 Hz.
Fix Number FIX7783938
Manufacturer Part Number 137221600
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
Fixes these symptoms
Installation Instructions
Merle from St.Joe, IN
Washer wouldn't drain
Replaced the drain pump Read more...
$69.38
In Stock
Tub Seal Assembly
Fix Number FIX459481
Manufacturer Part Number 5303279394
This seal helps prevent any leaking around the transmission of washing machines.
Fixes these symptoms
Installation Instructions
William from Leeds, AL
Once the washer filled, leaking around the spin bearing resulted
I followed the videos included with the parts on the site. Those videos were a life saver. It took a lot of liquid wrench and penetrating oil to free up some of the parts for removal, but the saving was well worth the effort. I spent extra time cleaning up the basket and tub as well as the trunnion. As it turned out the small rubber washer included with the metal washer had completely disintegrated but there was also a squealing noise indicating the spin bearing was in need of replacement. All in all it was difficult to remove the trunnion but everything else went well. Read more...
$68.32
Special Order
Inlet Hose - 5 FT
Fix Number FIX468114
Manufacturer Part Number 5303912532
$14.70
In Stock
Upper Spin Bearing Washer
Fix Number FIX473382
Manufacturer Part Number 5308002401
Fixes these symptoms
$73.06
In Stock
Spin Bearing
Fix Number FIX446536
Manufacturer Part Number 3204405
Fixes these symptoms
Installation Instructions
William from Leeds, AL
Once the washer filled, leaking around the spin bearing resulted
I followed the videos included with the parts on the site. Those videos were a life saver. It took a lot of liquid wrench and penetrating oil to free up some of the parts for removal, but the saving was well worth the effort. I spent extra time cleaning up the basket and tub as well as the trunnion. As it turned out the small rubber washer included with the metal washer had completely disintegrated but there was also a squealing noise indicating the spin bearing was in need of replacement. All in all it was difficult to remove the trunnion but everything else went well. Read more...
$76.28
In Stock
Shock Absorber Kit
Fix Number FIX3508101
Manufacturer Part Number 5304485917
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
Fixes these symptoms
Installation Instructions
JOSEPH from Olympia, WA
Two busted shock absorbers
The tight confines put a hammer out of the question, so I used needle nose pliers to work the pins out (using leverage against sections in the washer) and then bar clamps to force the new pins in. Bar clamps were critical to the successful installation of these pins given the lack of room I had to work with. Read more...

Appliance Type

Related Pages

Popular Gibson Washer Models