Food Waste Disposer Parts

$21.24

Garbage Disposal Drain Stopper

Fix Number FIX12726321

Manufacturer Part Number WC11X20163

The drain stopper helps prevent water from draining from the sink and through the garbage disposal.

Fixes these symptoms

Leaking
See more...

$39.58

Sink Flange

Fix Number FIX12722852

Manufacturer Part Number WC15X20161

The cushion mount forms a watertight seal between the garbage disposal neck and the mounting ring. It is made of black plastic and measures approximately 4.5 inches in diameter and is 0.125 inches thick. Be sure to disconnect power from the waste disposal before you begin this repair.

Fixes these symptoms

Leaking
See more...

$32.72

Splash Guard

Fix Number FIX11742344

Manufacturer Part Number WP4211334

This is a flexible rubber cover that fits over the top of the sink drain. It opens up in the middle and will allow you to feed water or food items into a garbage disposal while keeping liquids and smaller food particles from splashing back into the sink.

Fixes these symptoms

Garbage comes back up sink
Smells bad
See more...

Installation Instructions

Greg from Ridgefield, WA

There were 2 problems. KitchenAid does not have installation instructions for this model. One step in the take down/installation wwas tough.

I found that while KitchenAid did not have any info on KCD1250S1, it did have instructions for KCBD250S1 and the two are very similar. so I used those instructions - which were not as complete as one would like, but with some experimentation they gave me enough clues that it worked. First, do not remove the red cover or the Styrofoam that is underneath the plastic. Second, the removal of the disposal was easy once I learned that the key was to stick a Allen head screwdriver into one of the round metal openings that hide above the red plastic cover. Then shove the screwdriver (which will rotate the metal fitting) clockwise when you are underneath looking upward. Catch the heavy disposal when it decides to come loose. Do everything to get the new parts into place, it's easy. Put the Flange, seals and brackets in place and tighten the screws. The next step is putting the screwdriver into one of the rotating flange metal holes, then forcing the heavy disposal completely up into the flange fitting (I had to look down through the sink drain hole and guess where everything really was), and shoving the screwdriver (rotate the flange) counter clockwise, again when looking up from beneath the disposal. I suspect that if you do this a few times it gets easier. It now works perfectly. Read more...

$17.43

Flange Gasket - Fiber

Fix Number FIX6883604

Manufacturer Part Number WC03X10008

Sold individually.

Fixes these symptoms

Leaking
See more...

$12.72

Disposer Splash Guard

Fix Number FIX257945

Manufacturer Part Number WC3X124

$17.70

DISPOSER DRAIN ELBOW KIT

Fix Number FIX12722851

Manufacturer Part Number WC14X20160

This is an elbow outlet and gasket for a food waste disposer or garbage disposer. This part connects the disposer to the drain pipe in your home. If you notice a blockage or a leak, you may need to replace this part. It is black in color, made of plastic, and measures about 6 inches tall.

Watch the install video

$11.10

Hose Clamp

Fix Number FIX11740613

Manufacturer Part Number WP285655

This hose clamp is sold individually.

Fixes these symptoms

Leaking
Will not drain
See more...

Installation Instructions

Jacob from Center, TX

The drain hose had a hole in it and needed to be replaced

Removed the lower front panel, disconnected the hose and replaced it with the new one, then replace the panel. The most dificult part was getting my old self on the floor and unscrewing the panel nuts. Read more...

$7.95

Sink Flange Gasket/Seal

Fix Number FIX11742343

Manufacturer Part Number WP4211302

Fixes these symptoms

Leaking
See more...

Installation Instructions

Greg from Ridgefield, WA

There were 2 problems. KitchenAid does not have installation instructions for this model. One step in the take down/installation wwas tough.

I found that while KitchenAid did not have any info on KCD1250S1, it did have instructions for KCBD250S1 and the two are very similar. so I used those instructions - which were not as complete as one would like, but with some experimentation they gave me enough clues that it worked. First, do not remove the red cover or the Styrofoam that is underneath the plastic. Second, the removal of the disposal was easy once I learned that the key was to stick a Allen head screwdriver into one of the round metal openings that hide above the red plastic cover. Then shove the screwdriver (which will rotate the metal fitting) clockwise when you are underneath looking upward. Catch the heavy disposal when it decides to come loose. Do everything to get the new parts into place, it's easy. Put the Flange, seals and brackets in place and tighten the screws. The next step is putting the screwdriver into one of the rotating flange metal holes, then forcing the heavy disposal completely up into the flange fitting (I had to look down through the sink drain hole and guess where everything really was), and shoving the screwdriver (rotate the flange) counter clockwise, again when looking up from beneath the disposal. I suspect that if you do this a few times it gets easier. It now works perfectly. Read more...

Watch the install video

$8.04

Hose Clamp

Fix Number FIX11743008

Manufacturer Part Number WP596669

This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Albert from Unadilla, NY

noticed water was leaking in front of washer-right before we were leaving for vacation

Upon returning from vacation, we needed to do laundry-so I put some plastic under the washer and we did a load. The water was leaking from the seam between the lid and the back panel on the side with the hot and cold water connections- not the front. I removed two screws from the front bottom panel and two screws from the underside of the lid.Turning the washer on showed the leak was coming from the injection valve( it was brittle from age). The rubber injection valve was replaced and installed( using a little liquid soap to help the rubber hose to slip over the rubber injection valve) with a new clamp. The leak was fixed. Read more...

$14.16

GUARD

Fix Number FIX12070623

Manufacturer Part Number W11087190

This is a flexible rubber cover that is over the top of the sink drain. It keeps liquids and smaller food particles from splashing back into the sink.

Popular Food Waste Disposer Parts

Brands

Related Pages

Popular Food Waste Disposer Models

Food Waste Disposer Parts

Start With Your Model Number

Popular Food Waste Disposer Parts

Brands

Related Pages

Popular Food Waste Disposer Models