Cover 343373670
$3.99
In Stock
- Fix Number:
- FIX10418351
- Manufacturer #:
- 343373670
- Manufactured by:
- Metabo
Jump to:
Product Description
-
Works with the following brands:Metabo
-
Works with the following products:Angle Grinder, Miscellaneous
- Works with the following brands:
- Metabo
- Works with the following products
- Angle Grinder, Miscellaneous
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts Additional or alternate parts to consider.
View More
View Less
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
My angle grinder, after years of hard use made a popping sound and started to vibrate slightly. I noticed some black plastic protruding from one of the motor vent slots in the head of tje grinder. Turned out to be a chunk of the motor cooling fan assembly.
After disconnecting from power, I disassembled the grinder to figure out what was broken, checking all parts as I went along. Disassembly is pretty straight forward, starting by removing the grinding wheel, nut, shield and side handle. Remove the 4 screws and the cover of the bevel gear housing. A 9mm wrench is used to remove the pinion g
... Read more
ear nut, to allow seperation of the motor armature from the gear housing. Before pulling the armature from the handle assembly, you can remove the side covers from the handle assembly and gently pull the brush retainers out of the handle/ motor frame to allow clearance. All parts were fine other than the motor cooling fan that had lost a 5/8" chunk of fin section. The air baffle and cover were still useable but slightly abraded by the fan parts, so I ordered those as well, being inexpensive anyway. The motor brushes were still about 70%, and all bearings were in excellent condition. The only other issue was that the bevel gear lubricant was pretty dried out, so I ordered a tube of that also.
Once my parts arrived I reassembled the grinder- the fan assembly pressed on the armature assembly with hand pressure- just be sure to align the splines. The cover, baffle, and bearing were easily tapped on the motor shaft using a small deep socket to push only on the bearings inner race. The pinion gear then pressed on the same way, then is retained by the 9mm nut. The armature can then be put back into the handle housing, the brush retainers put back in place, and the side covers reinstalled. The bevel gear housing can be pressed onto the armature/ bearing with hand pressure, perhaps with some light tapping with a padded hammer. The gear housing was re- greased with new lube ( it was cleaned while disassembled) and the gear cover/seal/ 4 screws replaced. The wheel guard was a bit tweaked from being used for 15 years, so I straightened that out before replacing it. I purchased an anti- vibe side handle for the old grinder too, as the original plastic handle was getting a bit beat up. In short, a fairly easy and inexpensive repair of an excellent tool. All the parts received from fix.com fit perfectly and were top quality. Hopefully I'll get another 15 years use out of this tool.
Once my parts arrived I reassembled the grinder- the fan assembly pressed on the armature assembly with hand pressure- just be sure to align the splines. The cover, baffle, and bearing were easily tapped on the motor shaft using a small deep socket to push only on the bearings inner race. The pinion gear then pressed on the same way, then is retained by the 9mm nut. The armature can then be put back into the handle housing, the brush retainers put back in place, and the side covers reinstalled. The bevel gear housing can be pressed onto the armature/ bearing with hand pressure, perhaps with some light tapping with a padded hammer. The gear housing was re- greased with new lube ( it was cleaned while disassembled) and the gear cover/seal/ 4 screws replaced. The wheel guard was a bit tweaked from being used for 15 years, so I straightened that out before replacing it. I purchased an anti- vibe side handle for the old grinder too, as the original plastic handle was getting a bit beat up. In short, a fairly easy and inexpensive repair of an excellent tool. All the parts received from fix.com fit perfectly and were top quality. Hopefully I'll get another 15 years use out of this tool.
Read less
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Model Compatibility
This part works with the following models:
Fix Number: FIX10418351
Manufacturer Part Number: 343373670
Manufacturer Part Number: 343373670
Brand
Model Number
Description
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.