Models > KUDF204EPA01 > Instructions

KUDF204EPA01 Whirlpool Wine and Beverage Cooler - Instructions

Jump to:

All Instructions for the KUDF204EPA01
121 - 135 of 380
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Lev from Fanwood, NJ
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Plastic coating chiping-off
First I removed one screw that hold the element in place, lifted element about half an inch. I then pulled the element out about 2-3 inches and disconnected the wire. Then replaced two clips on top of element and re-connected the wire, put screw back and VUALYA....done!!!!!!!!!!!!!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mike from Camas, WA
Parts Used:
WP2196157
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.
Simply removed the old and replaced with the new part.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
RONALD from SHREWSBURY, MA
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Icemaker stopped working
Easy removel: remove one screw and loosen two others; unplug connector; swap actuator bar; replace
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Walter from Las Vegas, NV
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Leaking tray shorted heater
Removed the old ice maker and replaced with new.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Antioch, IL
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Water leaking out of Icemaker
I undid two top screws and one bottom screw. The tools came out of my cheapo walmart tool kit. I disconnected the power connector. I then put the new Icemaker in and waited for ICE. 12 hours later still no ice. I contacted Parts Select and before I knew it an new Icemaker was ordered and delivered to my doorstep. I received several emails to confirm the refund and re-billing of icemaker. I was absolutly astonished by how well they responded. I figured weeks after the first replacement came in DOA but two days later I had Ice and all was well.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lois from Thomasville, AL
Parts Used:
WP2196157
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Water tubing was accidentally broken from the back of the freezer.
Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christopher from Valley Village, CA
Parts Used:
WP2196157
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Movers broke the icemaker water fill tube shoving my refrigerator through the front door.
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeremy from Pittsburgh, PA
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
icemaker didn't work right.
Unbelievable experience. Ordered on Friday received on Saturday. Removed three nuts with a nutdriver, unplugged the old icemaker, plugged in the new one and replaced the three nuts. I went from order to ice in the bucket in about 24 hours. Thanks
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
greg from shalimar, FL
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)
replaced ice maker
three screws and a plug in and it was done!
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond D. from Farwell, MI
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
heater didn't thaw ice, stripped eject gears! no ice!!!
added lowering clips to brackets, plugged it in,
hung on sidewall. Plug in power, turned water on,
had ice in an hour. The written directions could be a little more detailed..I am very satisfied with the ease of installation.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph A from Sachse, TX
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Icemaker not working properly
The icemaker was an exact duplicate of the one in my refrigerator. I installed the correct shutoff bar on the icemaker and removed the tab for the water fill spout. After pulling the power cord I loosened the two top screws with a nutdriver and removed the bottom screw. I pulled the icemaker from the rear wall, away from the fill spout, and disconnected the wire harness. Installation was just the reverse of the removal.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stephen from Greensboro, NC
Parts Used:
WP2196157
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Old tube had cracked due to being frozen....
I followed the simple steps outlines in the great video! Thanks
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dean from Ames, IA
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Ice maker was flooding the freezer
After turning off the water to the fridge, I removed the 3 screws holding the icemaker, and unhooked the wire harness. I just reversed the process to reinstall and it took about 20 minutes, and we had a bin full of ice the next day.
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bill from Kuna, ID
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
The icemaker stopped making ice.
I first removed the door, very easy to do, then removed one screw that held the icemaker in place. I then unplugged the electricity to the frig, slid the unit out and disconnected the electrical harness. Luckily the harness on the new icemaker matched up with the original plugin on the frig so it wasn't necessary to change the wiring on the new part. I simply slid the new icemaker in plugged it in put the retaining screw in, the door on, plugged the frig in and started makinmg ice. Couldn't have been easier.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Scottsdale, AZ
Parts Used:
4317943
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Icemaker quit working
I removed the 3 screws that held the unit in place and disconnected the power supply from the front part of the icemaker. I then assembled the replacement icemaker and plugged it in to power supply. I then mounted it with the 3 screws that it required. (Tip): Note the top 2 screws do not need to be totally removed just loosen them enough to remove icemaker. I then cycled the iemaker shutoff arm several times and within 45 minutes I had my first ice cubes
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KUDF204EPA01
121 - 135 of 380