MWFW9200SQ00 Whirlpool Washer - Instructions

Opened lower front panel to access the motor controller. Took a picture of the wiring attached to the front of the controller. Removed two wiring harnesses and one wire with a retainer clip. Removed the faulty controller. Inserted the new controller, replaced the wiring, using the picture to insure correct positioning (although that really wasn't necessary because the wiring clips could probably only be put in the correct places). Replaced the front cover, plugged in the washer and fired it up.

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

Unplug washer. Open door. Look at the very bottom of the bellow and will see a spring that is connected to a small wire that runs around the bellow holding the outside on. Using a flat head screw driver insert it between the wire and bellow, pull down slighty. Grab the wire and gentley pull off. Now the outer part of the bellow will be free, pull it toward you, and off the water/soap despinser, then push it into the washer. Now look to the right side and you will see a screw head that is actully a big clamp ring around the bellow. This is the hardest part. Use a small rachet screw driver with a 7mm socket to lossen. Pull clamp off gently, you can now removwe the bellow. Put bellow back on in reverse. There will be a small tab on the bellow it goes to the top. Took about 2 hours.

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

The repair went very easy after locating the repair manual inside of the washer. The service manual gave all of the codes that the machine can give. Checked the F-70 code and it stated to unplug the motor control unit. Once that was unplugged the led lights came back on and it acted like it could run again. New unit put in in less than 15 minutes. I'd suggest to have it over nights because the unit I received through UPS was very badly damaged on the outside but plugged it in and it still worked. Two weeks running and a lot of laundry later; still going well.

Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $

Very simple repair had to remove door from Washer, loosen the seals so that I could remove the old hinge. Inserted new hinge place the door and hinge on brackets and tightened the screws. I was very pleased with the fast action in getting me my parts, less than 24 hours.Thank You.

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!

Replace water pump

Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

unplug washer from outlet carefully tilt back to get at underside of washer remove bottom panel. pump location lower right front. remove two hoses from back using pliers keep note on hose location. remove two bolts on underside of machine slide pump to the right to release from rubber holders to install reverse the process also good idea to use the new hose clamps that come with your new pump and the rubber mounts if they are included