MWFW8300SW01 Whirlpool Washer - Instructions

very easy repair watched videos to diagnosed problem. Removed old sensor and rubber seal replaced with new.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!

Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

Removed top of washer. Removed top front panel. Removed old front panel clamp. Removed front door panel. Removed old tub clamp. Then removed torn tub seal. Installed new tub seal. Needed two sets of hands to install new tub seal. Pretty tight installing the new tub seal around drum lip. Might be a good idea to heat up or let your new tub seal soak in water prior to installation. Once tub seal was installed, I installed new tub clamp then re-installed the door switch. After that, I put the front door panel back on. Then tightened down the door switch. Finally, I installed the top front panel and then the top of the washer.

Replaced the pump. Continued to get the F9E1 error. Removed and cleaned the drain pipe between the drum and the pump. Problem resolved.

I followed the steps from online videos to determine where the leak was coming from (cleaned the pump filter, still leaking; checked gasket and inlet hoses).

Finally, I discovered a wet area and cut on the drum-to-pump hose. When I removed the hose, I found that the culprit was a credit card that had broken into shards and slit the side of the hose. I was happy to see it was from the previous owners, which meant it wasn't my fault!

I did have a hard time removing the clamps (double-wire "rotor clip" or "spring clamps", according to Google) holding the hose to the drum and pump. This became a problem when replacing the hose as well. I was not strong enough to squeeze the ends together to loosen the clamp.

Getting the old hose off was easy enough, as was putting the hose back on. The problem was clamping it back on, as I mentioned.

I tried using zip ties, but this was a disaster! I tested it using a rinse and spin cycle, and the zip tie seemed to hold. However, the hose slid off during the first full cycle I ran and dumped at least 15 gallons of water on the floor. Clean up was not fun!

My recommendation (and what I finally went with) is to use hose clamps with the small screw that lets you tighten the clamp with a screw driver. I used that on both the connection to the drum and the connection to the pump and I've had no issues since.

Overall, it's a quick fix once you have the hose replacement and the right parts. If I'd gotten the hose clamps right away, I could have been done in 30 minutes.

Hope this helps and good luck with your repairs!

Unplugged washer , used shop vac to drain water through drain hose on washer. Removed both hoses from old pump. Removed electric plug, removed 2 screws from bottom of the pump. Then reverse the process.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

After further investigation I realized that the original dispenser hose from the soap bin to the inner tip was the cause of the leak. Before this repair, I replaced the bellows. And as part of that replacement process you have to remove the washer dispenser hose from the inner tub so that I could complete the bellows installation. However when I put everything back together the old washer dispenser hose was leaking terribly. This was fixed easily with a new hose and an 1-1 3/4 inch hose clamp. I found an installation video that allows you to come from the top down to replace this hose but for my model of washer and because the drier was stacked on top, I took apart the front of the washer since I learned from a different video how to do this in order to install the bellows. No more leaking at all with the new hose.

Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!

This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

I never did the repair because Partselect.com shipped the wrong part. Then they charged me a 2nd time to resend the correct part plus the fees for shipping the correct part overnight which I did not get it until 2 days later. Now I shipped both parts back & have to wait for a refund.
I will never order from them again!

Watched the videos which were key! Thanks Parts Select! Replaced Bellows and dispenser hose. Cleaned all areas really well where new hose and bellows attached. Ran the washer in "clean washer mode" twice. Not a drop leaking. Thank you!

First unplug the washer and turn water off..Next take off back of the washer ( I used a socket set). Then underneath the front load tub, take that panel off to get to the pump (there are 3 screws in the front panel). Then get a towel put it underneath the water pump. Next take your pliers and squeeze the tab holding the end of the drain hose where it connects to the pump, Slide the clip up on the pump connection, pull off hose ,make sure your towel is underneath the end of the hose.Next reach your hand through the back of the washer and squeeze the plastic holder w[th your hand to release the hose. Then pull old hose out and replace it the the new hose. Just reverse the steps to put it in..

I simply followed the video instructions which was presented very clear and the video shots was on point