MVWB765FW2 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eric from SMITHFIELD, UT
- Parts Used:
- W11259006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The left side of the where it connects to the washer was broken & getting worse
I took out the 4 torx screws holding the lid on, took the old lid off put the new lid on & replaced the screws.
From the time I took the new lid out of the box and had it installed was less than 15 minutes.
From the time I took the new lid out of the box and had it installed was less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Seminole, FL
- Parts Used:
- W11130359
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Out of balance code , shaking during spin cycle
Removed three screws on back to open top panel, used small vice grip to pull on suspension rod to unhook and remove from the drum. Remove and replaced one at a time so the rods keep drum suspended and prevent from dropping in the cabinet . Reinstalled top panel and done .Very easy completed in about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from MURPHY, NC
- Parts Used:
- W10810403
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
washer would start then stop with everything flashing
UNPLUG WASHER FROM WALL PLUG
Watch u tube on how to remove top and also cover on top circuit compartment
First find the service book taped inside front. PLUGand read to read codes
call up the error codes flashing
the code indicated a defective lid latch.UNPUG WASHER
went through testing the switch one of the contacts was defective and intermittent.
UNPUG WASHER unpug J connect from circuit board remove wiring and connect from lid
new wiring harness goes back same as old one and mount new lid switch. done
Watch u tube on how to remove top and also cover on top circuit compartment
First find the service book taped inside front. PLUGand read to read codes
call up the error codes flashing
the code indicated a defective lid latch.UNPUG WASHER
went through testing the switch one of the contacts was defective and intermittent.
UNPUG WASHER unpug J connect from circuit board remove wiring and connect from lid
new wiring harness goes back same as old one and mount new lid switch. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from CHASKA, MN
- Parts Used:
- W10919352
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Center Dispenser Wear
Used some essential oils in laundry to help with odor. (Doesn't work, don't bother. Just get better soap.) Oils caused damage to center dispenser tray. Bought replacement tray. Simply pull the old one out by pushing down on the tabs on each end, slide the new one in place. Maybe took 30 seconds. Price? Far too expensive for a plastic drawer, but what do you do?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from ELMIRA, NY
- Parts Used:
- W11097645
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Top panel was rusted above soap drawer
My husband watched numerous YouTube videos before tackling it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CLINTON TWP, MI
- Parts Used:
- W10810403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
broken lid latch
move washer to get to backside, remove necessary screws and hoses, slid washer top over, replaced lid mechanism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from EUSTIS, FL
- Parts Used:
- W11130359
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Replaced the suspension springs
The video was excellent in what needed to be accomplished. However it showed reaching inside the tub with vise grips to grab the old spring. This worked fine for removing them but the installation of the new spring did not allow my hand and vise grip to secure the new spring and pull it up and insert it into the retainer. I found that by taking a cord and putting it through the socket and retainer allowed me to pull straight up and seat it in the retainer a lot easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from INMAN, SC
- Parts Used:
- WPW10238319
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door alignment
I was sent the wrong part , when I questioned them said they did not have it so was directed to Whirlpool and they are making it and I might get it in May
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hoa from Greer, SC
- Parts Used:
- W10876600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No drain
Take the old one out and put a new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from INDEPENDENCE, KY
- Parts Used:
- W10752187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
the impellar mechanism wore out so stopped aggitating
Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!