WTW8000DW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernestine from CARRIERE, MS
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Making noise when spinning tub hit side of washer.
Remove top of washer suspension
Rod goes on side of tub .
Rod goes on side of tub .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia R from BROOKHAVEN, MS
- Parts Used:
- W10810403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Lid would not lock, therefore, washer would not start.
I watched a YouTube video first. Followed instructions exactly and had washer going in 30 minutes!!!! Part that I ordered was an exact fit! Thanks to partselect.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from BLOOMFIELD, NM
- Parts Used:
- W11723354
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
WASHER QUIT WORKING, FULL OF WATER, NO CODES. DETERMINED FROM INTERNET GOOGLE SEARCH THAT CONTROL BOARD WAS BAD.
HAD A HARD TIME FINDING ANY YOU-TUBE VIDEO THAT SHOWS MY EXACT MACHINE. MAYBE BECAUSE IT IS ONLY 3 YEARS OLD. FINALLY FOUND A PARTS DIAGRAM THAT SHOWED LOCATION OF CLIPS TO RELEASE THE CONTROL CONSOLE FROM THE TOP DECK. ONCE I GOT THE CONSOLE FREE, IT WAS ONLY A FEW MINUTES TO REPLACE THE BOARD AND CONNECT BACK UP. MY MACHINE HAS NO KNOBS ON THE FACE SO I COULDN'T USE THE "STANDARD" CALIBRATION TECHNIQUE. INSTRUCTIONS WITH NEW PART SAYS THAT RUNNING IN "CLEANING MODE" WILL CALIBRATE. i TRIED THAT BUT HAD TO QUIT AS WATER WAS LEAKING FROM THE BOTTOM OF MACHINE. THE NEXT DAY, I BAILED AT LEAST 40 GALLONS OF WATER OUT SO I COULD MOVE THE MACHINE OUT TO LOOK FOR THE LEAK. WHEN I REMOVED THE BACK AND TRIED THE MACHINE, I GOT AND F1, E3 ERROR CODE. SINCE I HAD THE WATER SHUT OFF, I FIGURED THIS WAS THE PROBLEM. BUT MACHINE WOULD ONLY PUMP THE REST OF THE WATER OUT, FLASH THE E3,F1 CODE OVER AND OVER. FOUND A YOU-TUBE VIDEO COVERING A MAYTAG WASHER WITH THE SAME SYMPTOMS. SIMPLE FIX WAS TO REMOVE THE AIR TUBE FROM THE CONTROL BOARD, BLOW INTO IT TO REMOVE ANY OBSTRUCTIONS AND WATER, RECONNECT AND DONE. SURELY THIS WOULD BE TOO SIMPLE BUT WHEN I PLUGGED THE MACHINE IN AGAIN AND HIT THE POWER BUTTON, EVERYTHING LIT UP LIKE IT SHOULD. I WENT BACK TO THE UTILITY SETTING FOR CLEANING THE WASHER. THIS TIME, NO WATER LEAKS AND EVERYTHING WORKED FOR THE 1 HOUR PLUS CLEANING CYCLE. I NEVER DID FIND ANYTHING LEAKING IN THE BACK OR UNDER THE TUB. I PUT ALL BACK TOGETHER AND MACHINE WORKS LIKE A DREAM.
REMEMBER- CONSOLE CLIPS ARE ON THE FRONT CORNERS OF CONTROL CONSOLE AND REQUIRE A FLAT THIN AND NARROW BLADE TO RELEASE THEM, SUCH AS A TABLE KNIFE. THERE ARE 2 SCREWS TO REMOVE FROM THE BACK PANEL THAT ARE INTO THE PLASTIC CONSOLE. REPLACEMENT SHOULD BE A 10 MINUTE JOB IF YOU COULD GET INSTRUCTIONS.
REMEMBER- CONSOLE CLIPS ARE ON THE FRONT CORNERS OF CONTROL CONSOLE AND REQUIRE A FLAT THIN AND NARROW BLADE TO RELEASE THEM, SUCH AS A TABLE KNIFE. THERE ARE 2 SCREWS TO REMOVE FROM THE BACK PANEL THAT ARE INTO THE PLASTIC CONSOLE. REPLACEMENT SHOULD BE A 10 MINUTE JOB IF YOU COULD GET INSTRUCTIONS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from MURPHY, NC
- Parts Used:
- W10810403
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
washer would start then stop with everything flashing
UNPLUG WASHER FROM WALL PLUG
Watch u tube on how to remove top and also cover on top circuit compartment
First find the service book taped inside front. PLUGand read to read codes
call up the error codes flashing
the code indicated a defective lid latch.UNPUG WASHER
went through testing the switch one of the contacts was defective and intermittent.
UNPUG WASHER unpug J connect from circuit board remove wiring and connect from lid
new wiring harness goes back same as old one and mount new lid switch. done
Watch u tube on how to remove top and also cover on top circuit compartment
First find the service book taped inside front. PLUGand read to read codes
call up the error codes flashing
the code indicated a defective lid latch.UNPUG WASHER
went through testing the switch one of the contacts was defective and intermittent.
UNPUG WASHER unpug J connect from circuit board remove wiring and connect from lid
new wiring harness goes back same as old one and mount new lid switch. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from DOVER, TN
- Parts Used:
- WPW10581874
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Washing machine would not drain and a drn code would show in the display. Once the machine filled all the way up with water. Sometimes it would not refill to rinse.
I removed the 2 hose clamps connecting to the pump, removed 3 screws holding pump in place, and disconnected 2 wires plugged into pump. Put the new pump on in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from RICHMOND, VA
- Parts Used:
- W11220230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not filling then timing out before load done
Turned off power and water. Removed hoses/Unplugged power. Removed screws to open and access control panel. Removed existing valve first by pinching off 6 wire connectors then screws securing valve to washer base. At this point, I replaced with new valve and reattached everything. I also added screen washers to both hoses as I suspect it was built up debris in original valve impeding water flow through valve that led to problem…
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from ELMIRA, NY
- Parts Used:
- W11097645
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Top panel was rusted above soap drawer
My husband watched numerous YouTube videos before tackling it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from MORENO VALLEY, CA
- Parts Used:
- W11101059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic frame broke that holds hinge in place
First lid came and glass was shattered n box was open,called was told they credited my account and reordered, still haven't received credit for the first lid and it's been 3 weeks,other than that it was 4 screws to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from CANADIAN, TX
- Parts Used:
- W11220230
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer won't fill with water, Error Code LF showing on display panel.
Watched and followed You Tube Video . "Solved: The Fix for a Whirlpool Washing Machine that won't fill with water." The video is a little over 8 minutes long. At that start of the video he encourages you to watch all of the video for special instructions near the end of the video. You need to do that! I put 30-60 minutes, but actual time was 4 days as I had to order parts and wait for the parts to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tricia from HARLEYSVILLE, PA
- Parts Used:
- W10780048
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Washer walking during spin cycle
Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from CONWAY, AR
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My washer was always off balance.
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TEXAS CITY, TX
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
machine wobbled violently
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CLINTON TWP, MI
- Parts Used:
- W10810403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
broken lid latch
move washer to get to backside, remove necessary screws and hoses, slid washer top over, replaced lid mechanism.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LONG BEACH, NY
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud banging during spinning
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from LINN CREEK, MO
- Parts Used:
- W11220230
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
no water to washer
a couple of issues to get valve out and off , 15 min. install and top back on!!!
Was this instruction helpful to you?
Thank you for voting!