7MWTW1500EM1 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Terry from KEYSTONE, IN
- Parts Used:
- W10837741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wanting to see this new energy efficient washer work, with the lid open
There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chet from CLEARWATER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
heavy loads did not spin dry properly
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BAKER, FL
- Parts Used:
- WPW10006384, W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Loose pulley
Tightened up the pulley as the video showed me that might be the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from OCALA, FL
- Parts Used:
- W10780045
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
washer was shaking bad
Replaced the suspension rods not an easy task but very rewarding to hear it running quiet again when spinning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Danville, PA
- Parts Used:
- W11481722
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer wasn't agitating.
First, this is the second time the transmission actuator went bad. The first-time washer was still under warrenty and I watched the tech replace it. This time warranty has expired and I'm mechanically inclined, so I ordered the part. Replacing was easy, unplug, tip washer up so you can get under it, remove plastic guard (two hex nuts) and remove actuator by removing two screws. Reverse procedure to install new actuator. The only caution I will say is when tipping washer if you have a wall to lean it against, perfect, just put something under it for saftey so it can't fall on you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BELLEVUE, NE
- Parts Used:
- W10837741
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Washer acted like the lid would not latch and stopped it from cycling.
My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from ROCKY FORD, CO
- Parts Used:
- W11307244
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The washer would not wash or spin.
I watched the instructions on line, and followed them. Completed the parts change with out any problems, but that wasn't everything I had to do to make the washer to work again. I had to clear all the fault codes that were on the machine. Then the washer started working in all the cycles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from ARIZONA CITY, AZ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Gear stripped on main spline
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY W. from CARROLLTON, GA
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
making noise when starting spin cycle
Watch video on the site and the insulation will be easy and take about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from GEORGETOWN, KY
- Parts Used:
- W10780045
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer struts were wore out
Removed the old and replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MAHWAH, NJ
- Parts Used:
- WPW10006384
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burning smell, ASSUMED it was the belt
Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anna from TAWAS CITY, MI
- Parts Used:
- W10837741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid strike broke
Removed old one (2 screws) slid in place and screwed in.
Was this instruction helpful to you?
Thank you for voting!
Found washer to not agitate, washer was making a noise like grinding plastic on metal type noise. Was not sure what was causing noise until finally realizing that agitator was not agitating during wash cycle. To verify concern I removed old agitator assembly and marked top of input shaft and turned
Removed cover from dasher assembly and removed 7/16 bolt, removed agitator assembly and reinstalled new dasher assembly and installed new 7/16 bolt with washer included. Installed cover and tested washer. Washer worked normal again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!