7MWTW1935DW0 Whirlpool Washer - Instructions

I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.

After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agitator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!

First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.

As far as repairs go, this one is really easy.

Pulled cap off top of agitator, loosened bolt down in center of assembly and pulled collar up with pliers.
Removed old dog ears and replaced. Need to be extra careful on direction of dog ears.

Very simple; even a cave man could do it!

Removed fabric softener dispenser. Inserted medium flathead screwdriver into slot on side of cover that is on agitator and pried off. Used socket wrench, socket and extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs (cogs will fall right out so make sure you check to see how they're in). Replaced cogs in the same direction they came out. Very simple!!

I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy

Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.

With the help of a You Tube video, which was watched first, then when the parts were delivered, the video was watched again, then we played the video back and paused it after each section was done so we could make sure we were doing the repair correct. The one thing I will mention that the video doesn't mention to do is, before taking the agitator out of the washer, put a mark somewhere on the agitator to tell you which end is the top. Just remember that the top( cap ) will be off, so that will not work. Otherwise it was a good, easy fix

got the parts from parts select and got the machine repaired quickly
what a savings
repair man would have been over 100 dollars
the shipping was more than the parts but I saved greatly with no repairman
love your site and the great savings
i really loved my washing machine and hating to lose it
was so satisfied that I could save it after all these years
thanks

Washer stopped agitating. I removed the clothes softener cup on top of the agitator by grasping and pulling up, inside the agitator I removed the inner plastic cap by grasping the 2 finger tabs and pulling up. There was a plastic retainer assembly with spring instead of the 7/16 nut referred to in other posts. I used a long 1/2" ratchet extension to remove the plastic retainer assembly, removed the top half of the agitator and replaced the cogs, then replaced the agitator, plastic retainer assembly with spring, snapped the plastic cap back on, and replace the clothes softener cup.

Removed the agitator assembly with a socket wrench and extension, replaced cogs, reinstalled assembly...took about 10 minutes because I dropped the assembly once, and had to reassemble it. An absolute "piece of cake."

Could be done in place, but it's easier to pull the full agitator assembly out first, and work at a table. Remove the fabric softener dispenser, then the plastic cap below (with rubber o-ring)- both pull out by hand. Reverse the now visible bolt with an extended 7/16" socket and pull the cog housing up and out, gripping with gentle pressure with pliers ( locking plastic tabs make this piece impossible to remove by hand). Once the housing is removed it's easy to separate the two halves with your fingernails and replace the cogs. I was able to reassemble everything and push it back down into the drum in about two minutes. Piece of cake- I highly recommend anyone with a tool box do this himself.

Snap off softener dispenser. Pop off top of agitator with flat head screw driver. Use long handled socket ro remove agitator fastener. Lift off entire agitator assembly. Flip upside down on floor. Secure top section of agitator between feet and carefully unsnap but lifting upper portion. Look at placement of existing agitator cogs in upper section between feet. Remove cog retainer. Note position of cogs. Replace one cog at a time making sure they are repositioned the same way. Attach cog retainer. Place bottom portion of agitator in alignment and snap. Flip over and reinstall on washer center assembly. Place bolt and washer back into assembly and retighten. reattach cover and softener dispenser (if you have one). Done! Less than 15 minutes.