7MWTW1899BQ0 Whirlpool Washer - Instructions

Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.

I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the agitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!

I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.

I watched your video, followed the instructions, and
in 20 minutes I had a new washer! The repair man estimated the cost for repair at $150, but I didn't want to spend that much money on a 20-year-old washer, so I ordered the agitator repair kit, cost $12, and it arrived the very next day! I did exactly what the video indicated and within 30 minutes my washer was agitating like never before. Thank you so much for the video instruction, it was fantastic.

Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!

I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.

Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....

Followed youtube video. Great instruction.

After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.

Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.

from start to finish was about 10 minutes. used screwdriver to pop off top cap of agitator. used ratchet with small extension to take out bolt for agitator. removed agitator, placed it on ground for leverage and pulled off top agitator. carefully observed old directional cogs. flipped top agitator upside down removed old worn out/ broken plastic cogs. replaced them with the new ones. hard to screw up they only install one way. kept top agitator upside down and put rest of agitator back on. flipped it right side up and pressed down hard for secure fit. placed agitator back in washer. reinstalled bolt. placed cap back on and was finished...25 year old washer working like new. $2.80 not including shipping...

Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!

Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.