7MWTW1905DW0 Whirlpool Washer - Instructions

Gently pry top of agitator off with small flat-blade screwdriver. Using the square end of a 1/2-inch socket extension, unscrew the plastic center "nut." Lift agitator off, remove center cone that holds the dogs, slip the retainer ring off, remove the worn dogs and replace. (Great opportunity clean the soap scum off the agitator!) Reverse the process to complete the repair.

Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....

The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Most of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina

We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.

Removed the four worn agitator directional cogs and replaced them with new ones

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agitator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!

remove top of adigator and remove bolt. remove plastic clip and cogs.replace in reverse order.

Part ordered was incorrect even though your website said that it was correct when I ordered it. Part sent back. Have since bought a new washer. Your contact person to return part was very helpful.

That OK , easy.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

Started by replacing the lid latch assembly but this did not fix the problem. Parts Select representative suggested replacing the drive pulley clutch assembly. I order this and a new shift actuator. Had difficulty installing the new black shift actuator as it has a different electrical connection location from the original red part. The plug on the existing wiring harness would not reach the socket on the new black shift actuator. I had to remove the socket from the new black actuator casing so the plug would reach the socket. Washer is now working.

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.