WFW8740DC0 Whirlpool Washer - Instructions

So I was unable to get my model number so I took the hinge off the washer and was able to order the part. Before removing the hinge I used a marker and marked the hinge location on the washer. Once I got the part I removed the T15 screws on the inside part of the door and separate the pieces. I was able to remove the white tube for all 4 of the pins and put them on the hinge. I installed the hinge an then i put the front door pieces back together again while it was laying on the floor. I though I put it in wrong but I was correct. Once i had the hinge on the door and the door reassembled, I was able to attached the hinge to the washer. The hinge comes off the washer by pushing up on it and to reinstall you push down. I tighten the 4 T25 screws using the marks on the washer and the door is alligned correctly. I am able to close the washer door with one finger instead of my whole hand.

Two people to screwdrivers, stretching the spring out and around and that’s the last part to go on

Removed the back panel removed the drain pump installed new one

Old dispenser part came loose from dispenser drawer area, hit the floor and broke two plastic connectors. Very small and fragile plastic tabs are all that retains the front of the dispenser drawer. Cost for those two parts over $100 retail.

Be gentle with plastic components.

Found helpful video on YouTube
Unplugged washer and moved out from the wall leaving the drain hose intact
Used vacuum pump to suck out water from front of washer (inserted hose inside front door gasket)
Removed back cover
Checked filter on old pump(clean on buttons, screws or missing jewelry)
Positioned light and mirror inside to locate screws attaching pump
Unplugged small wire as shown on video
Used wrench and socket to remove bolt head screws
Used adjustable wrench to release clamp on hose connector to the old pump
Pulled out old pump wiped up small water drips
Installed the new pump ordered and received from partselect
Hardest part was inserting the far back screws and reversing the righty tightly mindset…
P.S. washer is up and running great!

Removed back panel. Remove 4 8mm sockets on pump assembly. Replace with new pump. Only difficult because of limited clearance. But I'm huge.

I pulled out the filter and it was not pugged so I ordered a new pump and installed it, easy to do. That took care of the fault code and it was repaired. Being who I am I took apart the old pump and found that the pump had a build up around the armature of the pump motor. I cleaned it up and reinstalled it and the old pump worked fine. Now I have a spear pump for the next it fails. Easy repair that took less than 15 minuets to fix.
Happy to deal with Parts Select they have great shipping.

I took the machine top off, then removed the control panel, removed old wire ring clamps. Removed door, removed inner clamp, water inlet tube, and bellows. Lubed up the new bellows with food grade silicone. Replaced the water inlet, inner clamp, door, outer spring clamp, reassembled the washer body and control panel and then ate a pizza.

Took sometime to figure out the problem. A little difficult to replace part partly due to the drain pump with filter’s location in the washer. Mine is on its lower right rear. It’s reachable and yet difficult. Good luck!

Unsnapped the broken assembly and then proceeded to snap the new assembly pieces in place. VERY EASY! Even for a 74 year old woman ??

Took the back cover off. Took screws off to pump. Replaced pump. Did everything reverse. Tested to make sure.

Disconnect electrical plug. Remove rear panel from washer. Remove drain hose. Open filter on pump unit to drain water from washer ( use a catch pan to catch water) remove drain hose from drain pump unit. Remove electrical connector. Remove 4 mounting bolts. Remove drain pump assembly. Install new pump in reverse order. Once washer is assembled. Pour about a quart of washer into the drum so as not to run the drain pump dry. Enjoy your repaired washer

replace the door lock with the parts i ordered

The top and back were already removed from front load washer. There is no lower front access panel on my washer. I followed a YouTube video that showed a similar washer model with a drain pump that looked exactly the same. This video had the washer up on a work bench for easier access. My washer is in a very tight space and the best I could do was wiggle it out and set the rear corners on bed risers. There are 4 screws that take a nut driver to loosen. My nut driver was too long to fit. My sockets were too fat to fit. I took my socket handle and put on a smaller socket, then added a nut driver from a power drill. This made it short enough to fit. One screw was totally by braille. The pump came off easily. I lubed the gasket part of the new pump with liquid soap. It was difficult for me to push the new pump up, so I used a ball hammer to wedge it up bit by bit. I was able to twist the ball hammer head enough to keep the pump up while I put the screws back. The screws finished snugging everything up. Washer works great now! This was done by a grandmother and obviously not an appliance technician.

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.