4GWTW4800YQ3 Whirlpool Washer - Instructions

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.

Watch video on the site and the insulation will be easy and take about 30 min.

I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!

Removed the old hoses and screwed on the new hoses.

Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.

I removed the cover for the softener dispenser on the top of the agitator. Then reached in and removed the cover of the nut and washer which was very sticky and sealed with an o-ring. This took a bit of pressure. Then used a socket wrench with an extension to loosen the bolt and took the whole agitator out of the machine. Then I set the agitator on the floor and with a fine 12 inch long screw driver released the catches while turning and pulling the agitatior with my other hand and holding the lower agitatior on the floor with my feet. I then turned the upper part over and removed the cogs and holding mechanism.
Then I reversed the process after replacing the cogs with the new part. 25 minutes total.

I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.

Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes

Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.

Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put back in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.

Just watched the video. Take from a 63 year old. Who never fixed a washer. Thx a lot for the video it saved me a lot of money being on a fix income. and it was less than $ 10 that was included shipping.

The info. was really helpful