2DWTW4740YQ1 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kristy from Lebanon, NJ
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washer was making an awful screeching noise when agitating
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from OKLAHOMA CITY, OK
- Parts Used:
- WPW10131112, WP3949550, W10772621
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Agitator was not turning. Dogears were worn out
First need to remove cap on Agitator. Inside there is a washplate bolt. Remove bolt. Old Agitator will slide up. Pull washer off stem. Clean grooved stem very well. Use some sort of lubricant on stem. Slide new Agitator on to stem. Part will be very snug as metal and plastic do not mix well. (Lubricant needed) Use board to lay flat on top. Gently tap with mallet until fully seated. Install new bolt. Run test wash. (Helps clean wash tub from any foreign substances.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from LIVONIA, LA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lid lock not working.
Followed instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from ARKANSAS CITY, KS
- Parts Used:
- W10721967
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Making a loud noise for a while then stopped spinning
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from LENGBY, MN
- Parts Used:
- W10913953
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
screeching noise at times,Wouldn't spin out
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Cranford, NJ
- Parts Used:
- W10913953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would go from sense to done without running cycles. Sometimes the drum would make a quarter turn.
I followed the video published on this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PINE MOUNTAIN, GA
- Parts Used:
- 8212641RP
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Washer hoses due for replacement
Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from WHITEWATER, CA
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Not really a problem but the hardest part was moving the washer to lay on its back.
I simply followed Steve's instructions on video. Very easy repair. Washer works great, no jumping or vibrating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LONG BEACH, NY
- Parts Used:
- W10780048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Loud banging during spinning
Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TEXAS CITY, TX
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
machine wobbled violently
followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from CONWAY, AR
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My washer was always off balance.
I used a jack to lift the tub and unhooked the rods and replaced them. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SAN JOSE, CA
- Parts Used:
- W10404050
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Washer would not adgitate
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tuan from LADSON, SC
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
On Spin cycle washer jumping all over the place.
Just follow the video! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from CLAYTON, NC
- Parts Used:
- W10913953
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not step through the cycle steps, would not complete the washer cycle.
Per the instructions on the website, I:
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
1. Disconnected AC Power, turned off the water supply and disconnected the water and drain hoses from the rear of the washer.
2. Laid the washer front side down to access the bottom of the washer.
3. Remove the Pulley Guard ( 2 nuts.)
4. Removed the Shift Actuator Assembly (2 philips screws.)
5. Disconnected the electrical connector from the assembly.
6. Remove faulty Actuator and replace with replacement part.
7. Install the Pulley cover lift washer upright, reconnect water supply hoses and drain tubing, plug washer in and tested.
Problem is resolved, saved almost $250 by doing it myself!
Was this instruction helpful to you?
Thank you for voting!