CHW8990CW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Peter from Naples, FL
- Parts Used:
- WPW10730972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My washer was not draining
It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Rowland Heights, CA
- Parts Used:
- WP8540221
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Latch broke
Took less than 5 minutes to replace, So Happy;-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Lyndeborough, NH
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers
Whirlpool Front loader washining machine F21 error code
Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Dayton, TX
- Parts Used:
- WPW10730972
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Making noise, not draining properly.
Put towel down to catch excess water, opened drain screen, used pliers to remove squeeze clamps on both hoses, removed front hold-down torx-head bolt and slid pump assembly out. Compared new part to old and found 2 differences 1:no hold-down location in front for bolt,2: the rubber padded feet are not the same. I was able to remove the two screws on the right side and use just the rubber pad for support while sliding the left side in the slot and is was plenty stable and works just fine. I guess the Whirlpool Duet model is a bit different on mounting but everything else fit quite well, the washer is working perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from West Seneca, NY
- Parts Used:
- W11366227
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Leaking flex pipe
Perfect part...saved me hundreds on labor. Thanks!
Was this instruction helpful to you?
Thank you for voting!