7MWFW80HEBW0 Whirlpool Washer - Instructions

Watched this video on the website and went to work. Went very easy and smooth with removing the door. A pair of pliers works fine for outer ring. Kind of challenging by yourself, but I got it on in less than 5 minutes. Pliers in one hand and flat head screwdriver in the other to work the ring on. Much cheaper than paying someone to do it. 2 out of 10 for difficulty.

Removed the old hoses and screwed on the new hoses.

The repair was easier than the troubleshooting. Figured out the hot or cold water supply valve was failing which allowed water to enter the tub via the dispenser leaving several inches of water on clean clothes or the empty cylinder.

To replace the valve you need to first shut off the hot/cold water supply and remove the hoses. (I took this time to replace the several year old hot & cold water supply rubber hoses with metal braided hoses. I also took a wire brush to the threads of the copper spigot removing any built up corrosion or gunk.) Next you need to remove the 3 1/4" sheet metal screws which secure the top panel of the washing machine. I always take a few pictures of the old part, hose, and connectors just to make sure I replace them in the same locations.

After removing the cover you can use clamp removal/installation pliers, vice grips, or a similar tool to remove the clamps for the hot and cold water to the detergent/bleach/softener dispenser.

Then, remove the electrical connectors on the valve and if you want label them with their locations on the left or right facing the rear of the washer if you want but they are pretty much self-explanatory. They have little retention clips which need to be disengaged in order to be removed from the valve assembly.

Next, remove the hoses and then the three sheet metal screws attaching the valve to back panel of the washer. Install the new valve assembly and then attach the hot and cold water hoses using the clamps to the detergent/bleach/softener dispensers. Then, attach the electrical connectors to the new valve and listen for the clip to engage and gently pull back on the connector (not the wires) to ensure they are properly attached to the valve.

Reconnect the hot & cold water supply hoses from the building pipes and turn-on both spigots or ball valves. Check for leaks and then plug in the washing machine and run a load to test the normal operation. I would leave one piece of dry clothing in the tub after running a load and leave it for a few hours to ensure the new valve is working as advertised.

If there are no further leaks, you are done! Way to go!

Followed internet instructions

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

remove power to machine
disco the water lines

removed the back of the washer then removed the top.

remove leaking water valve by removing the hoses then removing the valve assembly.

replaced with new,checked for leaks

reassembled washer

Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio

Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.

I am still waiting for the correct part to arrive, I was sent a part but it was the wrong part, the wrong part number and it was nothing that would work on a washing machine. I think someone else ended up with my part and I got theirs.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

Did the repair just like the video on your website. Was really easy.

Replace front legs. Very easy fix.

This was a super easy repair that completely fixed my issue. My washer was showing the same F8E1 error code on most loads, and would not run special cycles, only the normal wash cycle.

With the help of Google, I diagnosed the issue as a water fill error and understood that the inlet valve wasn't working. I bought this part, watched an instructional YouTube video, and replaced the broken part in about 25 minutes, start to finish.

To do the repair, I disconnected power and shut off water to the machine, then removed the back panel of the washer. Next, I unhooked the wires and water tubes connected to the old inlet valve and pulled it out of the machine. I snapped the wires into the correct ports on the new valve, attached the water hoses, slid it into position, and secured it with the set pins, then reattached the back panel on the washer. I plugged the machine back on and opened the water line. Everything works now, including special cycles.

Replaced the whole valve.

Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.