7MWFW72HEDW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Keith from MILFORD, MI
- Parts Used:
- W11415987
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Plastic shock slide broken
Unplugged the unit and remove the back cover of the washer. Broken shock was the right rear one so easy access.
Used channel locks to twist the upper and lower portion of the shocks to unlock them from the washer.
Installing the new part, it is advisable to clean the washer base cover that the shock fits into. Corrosion can make it difficult to insert shock tab and twist if not cleaned. I had to use the channel locks to twist, but be careful as the locking tabs are plastic.
It is also advisable that when you have the back cover off, that you clean the washer filter.
Used channel locks to twist the upper and lower portion of the shocks to unlock them from the washer.
Installing the new part, it is advisable to clean the washer base cover that the shock fits into. Corrosion can make it difficult to insert shock tab and twist if not cleaned. I had to use the channel locks to twist, but be careful as the locking tabs are plastic.
It is also advisable that when you have the back cover off, that you clean the washer filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from SALT LAKE CTY, UT
- Parts Used:
- WPW10562025
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
The clear plastic part that attches to the internal drain hose was cracked by the movers
Well, I am a 66 year old Grandma. I had to take off the entire back panel... no big deal ... then make sure to remember how the hose attaches to the bottom of the machine. Taking the clamp off with whimpy pliers was a little difficult due to the location. The most difficult part was laying on the floor and trying to use the stupid pliers that kept slipping off the clamp and try to shove the new hose on in the correct position. I just didn't have the grip power and manuverability to grab ... squeeze ... push the internal hose at the same time. I finally got it attached after 33 minutes. The rest of the hose attached litterally in a snap. Replaced the back panel and good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from LAKE STEVENS, WA
- Parts Used:
- WPW10605427
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Error Code F01 E09 (Drain Issues)
Unplug appliance. Remove the back panel with the 1/4” nut driver and cordless drill. The pump is located as you face the back of the machine on the bottom. Remove four screws that hold pump in. Reverse the process and install new pump. Check the filter and clean out the housing.
Reinstall back panel and plug back in. Run a test load (no clothes) and test drain.
Reinstall back panel and plug back in. Run a test load (no clothes) and test drain.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Lennon, MI
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Ardmore, AL
- Parts Used:
- W10763470
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had to install shipping bolts so we could move the washer
Really was not a repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!