CAM2762TQ0 Whirlpool Washer - Instructions

It took me awhile to figure out how to get the shell off the washer frame. (I didn't know about flipping it on its back). Once the moving parts were revealed, the water pump was staring at me with both ports. I turned the machine on and saw that the leak was coming from the pump.
1. Cut power
2. unclipped pump with pry with screwdriver
3. detatched both hoses - flood ensued
4. gently pulled pump off transmission
5. replaced pump

I reccommend doing this repair with empty tub.

First, disconnect from power & turning off the water. Then, accessed the part by tipping the unit back enough to work. Remove the hoses by loosening the spring clamps. Here is where things got a bit sticky. The pump motor shaft had corroded enough to make removal of the pump a wrestling match of sub-WWF levels. Once forced off, additional time was spent removing corrosion from the shaft to facilitate fitting the new unit. A little lube was used here. Re-assembly was quick & washer was righted, plugged in and returned to service. It is a simple repair which can, with a little acting ability, be portrayed as a monumental task requiring super-human strength & the wisdom of Solomon. I played the part well enough to merit a huckleberry pie for my effort & sacrifice! Thanks!

I followed the instructions in the video on the part page (part #PS11741239), which was also conveniently linked in the item shipped email. The replacement of the part was very easy ... the hard part was balancing the washer again (kitchen floor seems to have sunk in the middle). Back to normal function without having to suffer a flood first. Thanks.

Replacing the clutch was easy but unfortunately did not fix the washing machine. I couldn't get the agitator loose at first, but it came loose when I unbolted the motor and transmission assembly. After replacing the clutch and reassembling the motor, I tilted the washer back up and found that the basket in the center under the agitator was cracked all the way around and that was why it wasn't spinning. It was also why the clutch was burning--trying to spin a basket that wasn't centered in the drum anymore. This washer is over 25 years old, so I decided not to replace the basket, since a replacement is about $400. A good attempt at an inexpensive repair, but unsuccessful.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

Removed washer shell by instruction via video, then easily installed break hose and clamped it back on to water line and water dispenser. Works like a charm! No more leak

Very easy replacement. The new hose was more like a formed radiator hose and fit exactly.
Removed two screws at rear of control panel and separated the rear cabinet panel from the front cabinet enough to get to the water valve. I then disconnected the break hose from the valve by compressing the spring clamp. I then disconnected the other end from the washer water inlet by also releasing another spring clamp.
The new hose was installed using the same clamps. The cabinet was reassembled and washer tested for leaks.

Inserted new drain hose thru back and snapped into place. Tipped washing machine back, clamped new hose with pliers.

Just changed out the old pump with the new one. It went very quick and smooth!

We had to take the motor off and find the part that holds the spring, took longer to fix as we are older people and took a brake after every spring. We used YouTube videos to help us I am thankful for this site and cheap prices.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

replaced missing screw and pad and now machine works perfectly

I disconnected the water lines and pulled the washing machine over so it was lying on its front. I removed two screws on the bottom edge of the back, and then puzzled over how to get the back off. I ended up removing the screws that held the control panel on, removing the wiring harness, and taking the control panel/head off. This exposed two metal clips that I was able to unhook. I unhooked the water valve from the back, disconnected the electrical connections, removed the water line, and replaced the valve. Then I puzzled about how to put it back together for a bit, and basically just reversed the order I took it apart.

I tipped up the machine and had my wife hold it.
I removed the two hoses with water pump pliers. Then , I removed the two clips with my fingers. The old pump came off in my hands. I installed the two hoses on the new pump with my hands, lined up the pump drive with the hole pushed it in and re-attached the two clips with my hands.
The whole job took maybe five minutes. The hardest part of the job was conviencing my wife that there was no danger involved with the process.

After unplugging power and disconnecting water drain hose, I pulled the washer out aprox four feet from the wall and leaned it back against the wall. I then used a lamp at the end of an ext cord to light up below the washer where the water pump was attached and it was easy to remove and replace! I carefully replaced the washer in its original location and reconnected power and drain hose. The job was complete in 15 minutes! Wow!