WFW9600TA01 Whirlpool Washer - Instructions

After replacing the Water Inlet Valve and Flowmeter the F20 error message stopped. However, after ordering and replacing the Water Pressure Sensor the F35 error message and the SUDS error message stopped and the washer is finally working.

First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps

slid new baffle into place. No directions with new part, fortunately it was easy to figure out how baffle locked into place.

Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately $150.00 bucks in repair service fees.

First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws the cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott

looked repair on you tube followed instructions. took off broken latch. compared to pictures on sites. ordered part. part arrived in 2 days. put part on. suggest using first method quick and easy.

baffle just clicked into place by aligining tabs on baffle with openings on drum. very easy.

Removed washer door from washer. Lay door on work bench (table). You need to remove screws from around most of the washer door to remove broken hinge. Install hinge into door frame. Fasten all screws for hinge and door frame. Reinstall complete door assembly onto washer with removed screws. Helpful to have some hold door for ease of alignment. Tools used: 1/4 inch torque #15 bit with 1/4inch nut driver.

Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Everything went great from order to done. Very happy

I started getting this error; Browsing around the net, I came to know it is because of SWITCH-WL going bad. The part number is W10156252 and part name is also called as Switch, analog pressure sensor.

I removed the top cover of the washing machine, just need to remove two screws from back, top cover will come out. This switch is present on back right side of the machine. It was easy to remove the part from the machine; but make sure to see how the wire is connected to the part before you remove the wire from the switch. It is easy to connect the wire and put it back.

After changing this machine looks happy.

Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

After receiving the hinge and screws, I watched the on line video at the website. I removed the door and hinge from the washer, removed the hinge from the door and re-installed the new hinge. The entire process took less than 15 minutes and reattaching the new hinge to the machine was a breeze. The replaced hinge is smooth as silk and all is back on line. Great service from the crew at this site. Shipping was very quick (ahead of the scheduled arrival) and the CSR was very cordial and professional.

This part slides in and snaps in place, a 15 second job.