1CLXR7244PT0 Whirlpool Washer - Instructions

Job was easy! Just remove the top cap with a screw driver. With a socket and extension, remove the bolt that holds the agitator to the transmission shaft. Pull up on the agitator and lift it off the shaft. I had to use the screw driver to pry off the center piece that held the cogs because it did not what to separate from the rest of the agitator. Removed the pieces of the old, broken cogs, cleaned up the parts and installed the new cogs with the center piece upside down. I then took some silicone lubricant and lubed the area the cogs rub on and the opening the center piece spins in on the rest of the agitator. I then removed the Thrust Spacer on the mail part of the agitator but just lifting off the old one and putting on the new one. Then, with the center piece that holds the cogs upside down I inserted it into the upper corkscrew section of the agitator so that the cogs would not fall out. While holding the two pieces together, I turned it back right-side-up and installed it back onto the other part of the agitator and then on the shaft. Re-installed the bolt and tightened with the socket. That's it! It sounds more complicated then it really was.

First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ears were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.

First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done!

First I watched the vid, from this website that showed how to replace a pump on the Whirlpool model I have. It was very helpful. Then, on the same web page as the vid for washer pump replacement several DIYers describe how they did the repair and rate how difficult it was. This also was very helpful. The info from these two sources confirmed to me that it was the pump that was leaking. Tilting the washer back far enough so I could see the pump also visually confirmed it was the pump.
If the pump had come off easily I would not have had to take the cabinet off. All I would have had to do was lay the washer on its' back to get the pump off. But noooo, the pump was rusted so tightly to the motors' shaft that I had to be more aggressive, to remove the pump, than the measures mentioned in the vid.
After finally getting the pump off I saw that the end of the motors' shaft had corroded and was misshapened enough so that I had to "persuade" the new pump onto the shaft.
I also ordered these parts (1. Direct Drive Coupling 2. Agitator Repair Kit and 3. Clutch Assembly) after I read in the DIYers descriptions that many of them, who changed their pump, also changed these parts. Since my washer was 15 yrs old it made sense to replace these parts which usually wear out before the pump.
Unfortunately, after I got everything reassembled the new pump leaked more than the old one. Guess I over-"persuaded" the new pump onto the shaft. That, and I don't think the new pump is as well built as the original so it couldn't take much persuasion.
Now I either: 1. buy a new pump and motor or 2. buy a new washer which is what I'll most likely do.
If I had a do-over I would only get the pump. If it worked properly with no leaks, then I would buy the other 3 parts, if it didn't work, I would only be out $40 instead of the $95 I'm out for the 4 items. Being frugal or, as my family says, "cheap," I do have to be careful. There is a point where repairing something old is more a point of pride than good sense. I don't know where that point is and I definitely wouldn't have brought this up if the new pump had fixed the washer.
Also, after struggling for quite some time to put the cabinet back on, I Googled "how do I get a Whirlpool washer cabinet back on?" After watching one of the vids Google answered back-I was able to put the cabinet back on in less than 10 minutes.
I hope this has been helpful. Happy DIYing!

The repair itself was very simply, probably largely due to the design of the machine which made getting to, and replacing the two faulty parts a cinch. Just unscrew the two screws on the motor brackets which hold the motor down, and remove the brackets. Then remove the two smaller brackets which hold the pump to the motor. Then remove the two clamps and hoses from the pump. Lastly disconnect the power supply from the motor and the pump and motor will then come out as one unit. Simply reverse the process when reinstalling the new pump and motor. I used a bit of oil to lubricate the new motor shaft but I am sure it probably isn't necessary. The job should take no more than half an hour tops.

1. remove 2 hoses at pump using pliers to open hose clamps and sliding them out of the way.
2. remove 2 retainers holding pump with screwdriver.
3. remove old pump and install new pump
4. clamp pump using retaining clips
5. re-connect hoses

Disassembled the control panel and replaced the water level sensor, but not the hose - bad idea. It was probably just the hose. The thing tested fine for 3 fillings. I told my friend to watch it closely for the first couple of loads, because I thought the level was not consistent? - but she didn't. More water on the floor. Replaced the hose and it's working fine. Thank you.

I'd noticed for a while that our 15-year-old Kenmore washer was filling slowly, but when it started to take 30 minutes to fill to the "medium" level, I knew something was really wrong. There was plenty of water pressure, so I replaced a hose that was loaded with minerals and cleaned the filter (also clogged with minerals). But that didn't help! So I ordered a new water inlet valve, and replaced that. There's nothing tricky about the repair -- the hardest part is opening and closing the washer, for which I found instructions online. (Even so, it's the most time-consuming part of the project.) The result is the washer now fills as fast as when it was new. Just for fun, I took apart the old valve and expected to find it encrusted with minerals, but it looked fine, so I'm not sure where the actual breakdown was. But since the part only cost $25 -- less than a service call, for sure -- I was very happy to use a half hour of my time and keep the machine going a while longer.

It was extremely easy. I removed the plastic cap under the softener dispenser, removed the nut and washer that holds the upper agitator in place and then replaced the parts that came in the kit. The most important note for those who may be doing this job is that the o-ring for the cap under the softener dispenser, the seal washer for the bolt and the thrust spacer under the upper agitator all came with the kit. I did not realize that and ordered them all seperately.

Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, screw). Reassembled washer then ran wash for a cycle. Successful fix.

Although your website mentioned removing 2 screws to open the control panel, it took a while to realize there were 2 screws and 2 hex nut screws to open it followed by 15 minutes of efforts to release the control panel from the top of the washer by sliding it forward. After that it took 2 minutes to replace the switch; the web comment of keeping the lid open was helpful.
Unfortunately, the lid switch was not the problem; replacing the timer did the trick, was very easy with the control panel already opened and required the purchase of 1/4 and 3/16 hex nut drivers.
Parts, shipping and tools cost $110 but the success of the repair with your parts and advice was priceless.

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

First I removed the two screws holding the main controller located on the back. I then slide forward the hole controller and I pulled out. Disconnected switch located on your left. (remember to place down washing machine lid before installing the new switch.)

Removed softner dispenser, removed bolt on top of agitater,replaced parts supplied with repair kit.
Directions were inclosed in package that were easy to follow.I ordered Thrust spacer not knowing it was included in repair kit.

I WAS VERY PLEASED WITH YOUR WEB SITE AND DELIVERY TIME.

Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The rear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.