WFW9600TB00 Whirlpool Washer - Instructions

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.

Replaced pump assembly

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.

Took old one off and put the new one on. Was very easy. Hardest part was disconnecting hose clamps, which was still easy

Easy peezy!! Next day delivery, as promised for parts that could not be found anywhere else. I placed the baffles in the washer and clicked them in using both hands one by one. I'm petite and weigh about 110 lbs. The total installation time was less than 2 mins. I was given a $200 quote just for installation but, spent less than $100 and installed myself. Thank you!! I will not wait so long and shop around next time. I'm going straight to partsect.com to save time and money. Although I have to buy new clothes now since my washer put holes in all my clothes. But, the problem is finally solved and I am so grateful.

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

After diagnosing codes noticed no drain replaced pump asm

This was so easy to swap the parts out. The plastic hooks that hold the pieces inside our washer had just worn out. We put our washer and dryer through LOTS of use and I am amazed it has hold on this long! The broken piece just popped out and the new piece just snapped right in. Thank you for your speedy shipping and the great price.

I did not replace the pump body. I just removed the motor with the 3 screws. Put the new one on. This way I did not need to mess with the hose clamps.

The drum baffle came off. This website provided a diagram to make ordering the part easy. It was reasonbly priced and came in the mail very fast. I had it installed in my washer within 5 minutes. Excellent experience. Thank you.