WFW9200SQA11 Whirlpool Washer - Instructions

unhooked two water lines & electrical plugin unbolted old pump and installed new pump. took about 15 minutes.

After receiving the hinge and screws, I watched the on line video at the website. I removed the door and hinge from the washer, removed the hinge from the door and re-installed the new hinge. The entire process took less than 15 minutes and reattaching the new hinge to the machine was a breeze. The replaced hinge is smooth as silk and all is back on line. Great service from the crew at this site. Shipping was very quick (ahead of the scheduled arrival) and the CSR was very cordial and professional.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Unhooked two hose clamps took two screws off put new aprt on hooked back up works great

removed bottom panel and took out pump and replaced it with new one

Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.

My husband removed the bottom panel of the washer and removed the old pump with two screws, then removed the water hose coming into the pump and unplugged the electrical push in type plug from the side of the pump. Simple reversed the process to instal the new one and replaced the front panel. Simple really...far more so than calling a repair man.

My husband and son removed the old pump and replaced it with the new pump assembly. The whole process took about 30 minutes max.

It was so easy my wife replaced the part.

simple repair. After reading other reviews my husband was confident he too could do the repair. He was right, we were so very glad not to have had to call for service.

I had to cut new slots in the metal base of the machine cabinet to accommodate the different configuration for the rubber boot assembly. Thankfully the new pump works like a charm.

Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair

removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.

1. Turn of hot and cold water valves. Disconnect the hot and cold water hoses from the unit back panel
2. Use a nut driver to unscrew the top screws from the unit back panel
3. Remove the top cover
4. The valve is located at the top left corner
5. Use a torx driver to unscrew the screw off the valve unit
6. Unclamp and remove the hose from the valve unit
7. Disconnect the electrical plugs from the valve unit
8. Remove the faulty valve unit
9. Connect the electrical plugs to the new valve unit
10. Insert the hose and clamp into the new valve unit
11. Place the new valve unit to the top left corner of the washer and secure it with the torx screw
12. Re-cover the top cover and secure it with screws
13. Reconnect the hot and cold water hoses
14. Re-open the hot and cold water valves.
15. Turn on washer and verify there is no leak

Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement broke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.