7MWTW1712AM0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from OXLY, MO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Banging when in spin cycle.
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Washer drum banging on spin cycle
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from Liberty Lake, WA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Top part of agitator quit agitating in one direction.
First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Wetumpka, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
worn our Agit-dogs, agitator wouldn't pull clothes down
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canandaigua, NY
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator stopped turning
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from Delanco, NJ
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
upper agitator not spinning
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Little Rock, AR
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator would not agitate properly
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the agitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lindenhurst, NY
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top partion of agitator turned in both directions by hand and was not driven by the motor.
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Depeturie from Madison, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top of Agitator would not rotate
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from ANDOVER, OH
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
top part ofagitator not turning.
Followed instructions on website video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Penu from SAN MARCOS, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washer agitator was slipping
Removed the agitator cap, then removed the plastic, spring loaded retaining part (needed a square head tool). Once out, the cog retainer came out, replaced all four cogs, and replaced in reverse. Easy as pie & took 10 minutes!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Michigan City, IN
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The washer quit agitating
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathon from LOCKPORT, KY
- Parts Used:
- 80040
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plastic gears wore down not allowing top half of agitator to spin
Popped off top of softener cup. Pulled out screen. Used nutdriver to back out the only bolt holding the agitator on. Pulled it off popped out plastic "gears" and popped new ones in. Put back in reverse order. Done in 5 minutes....worked perfectly! Easy!!! Thanks !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Clawson, MI
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Agitator was spinning freely
Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble
repeat process to re assemble
Was this instruction helpful to you?
Thank you for voting!