WFW70HEBW0 Whirlpool Washer - Instructions

Unsnapped the broken assembly and then proceeded to snap the new assembly pieces in place. VERY EASY! Even for a 74 year old woman ??

The repair was easier than the troubleshooting. Figured out the hot or cold water supply valve was failing which allowed water to enter the tub via the dispenser leaving several inches of water on clean clothes or the empty cylinder.

To replace the valve you need to first shut off the hot/cold water supply and remove the hoses. (I took this time to replace the several year old hot & cold water supply rubber hoses with metal braided hoses. I also took a wire brush to the threads of the copper spigot removing any built up corrosion or gunk.) Next you need to remove the 3 1/4" sheet metal screws which secure the top panel of the washing machine. I always take a few pictures of the old part, hose, and connectors just to make sure I replace them in the same locations.

After removing the cover you can use clamp removal/installation pliers, vice grips, or a similar tool to remove the clamps for the hot and cold water to the detergent/bleach/softener dispenser.

Then, remove the electrical connectors on the valve and if you want label them with their locations on the left or right facing the rear of the washer if you want but they are pretty much self-explanatory. They have little retention clips which need to be disengaged in order to be removed from the valve assembly.

Next, remove the hoses and then the three sheet metal screws attaching the valve to back panel of the washer. Install the new valve assembly and then attach the hot and cold water hoses using the clamps to the detergent/bleach/softener dispensers. Then, attach the electrical connectors to the new valve and listen for the clip to engage and gently pull back on the connector (not the wires) to ensure they are properly attached to the valve.

Reconnect the hot & cold water supply hoses from the building pipes and turn-on both spigots or ball valves. Check for leaks and then plug in the washing machine and run a load to test the normal operation. I would leave one piece of dry clothing in the tub after running a load and leave it for a few hours to ensure the new valve is working as advertised.

If there are no further leaks, you are done! Way to go!

Followed internet instructions

Replaced the whole valve.

Replace front legs. Very easy fix.

Removed old pump, stripped down wires, added new pump, soldered the wires from washer to replacement pump, and hooked up hoses, tested and finished install. Was actually pretty easy. Just needed to make sure to get all the water was out of the hoses and pump before removing connection points.

Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.

Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.

I took the machine top off, then removed the control panel, removed old wire ring clamps. Removed door, removed inner clamp, water inlet tube, and bellows. Lubed up the new bellows with food grade silicone. Replaced the water inlet, inner clamp, door, outer spring clamp, reassembled the washer body and control panel and then ate a pizza.

Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.

Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.

1 Pull the machine away from the wall.
2 Unplug the machine.
3 Remove three screws in the back on the machine that secure the top
4 Remove the top
5 Remove the water lines that are connected to dispenser
6 Remove the Detergent tray
7 Remove one 1/4-inch screw that secures dispenser to the washer brace
8 Remove two torques tip screws from the front of the dispenser
9 Remove the outer ring securing the washer seal
10 Disconnect the rub hose connected at the front of the dispenser at the bottom
11 Reinstall the New Dispenser in reverse order
12 Test for leaks

Old dispenser part came loose from dispenser drawer area, hit the floor and broke two plastic connectors. Very small and fragile plastic tabs are all that retains the front of the dispenser drawer. Cost for those two parts over $100 retail.

Be gentle with plastic components.

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.

Really was not a repair