3LWTW4840YW0 Whirlpool Washer - Instructions

Removed the agitator with a socket wrench and replaced cogs as directed in repair video.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

First I came to this web site and discovered some directions from other customers. I then followed those directions to disassemble the agitator. I removed the softener cup by pulling up on the blue plastic retention ring. I then used a flat head screwdriver to remove the plastic cap by placing the screwdriver into the slot on the side and prying it off. Next I used a 3/8 socket and extension to remove the bolt which holds the agitator to the shaft. After the bolt was removed I pulled up on the agitator and removed it from the washing machine. To remove the upper section of the agitator, I placed it on the ground and holding the base with my feet, I pulled on the upper section. I then removed the dog ears, verifyed the problem and ordered the parts (dog ears). The parts arrived in less time than promised, were installed in about 5 minutes and I was back to doing laundry. When you reassemble the agitator, turn it upside down to install the dog ears so they do not fall out.

Removed the fabric cone from center of agitator pop out the plastic cover inside, remove bolt in center pull on agitator, remove cam holder and replace cams.
repeat process to re assemble

disassembled two halves, cogs just sitting there, replaced, re-assembled

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.

First take the top cover off, second using socket to turn the nut loose at the center, then removing the plastic holder which has four directional cogs in it, replacing them with new one.

I removed the fabric softner dispenser,removed the inner cover,removed the 1/2" bolt holding the upper agitator to the lower agitator and pulled the upper agitator up and out.Remover the cog holder from inside the upper agitator and replaced the old cogs with the new.They simply set loosely in the holder.I then reversed the process of putting the agitator back and bolting it in,inserted the small cover and dispenser.The entire job took about 5 minutes at most.

The dogs (directional cogs) cause the upper portion of the agitator to turn in one direction only. The clothes don't get clean unless this happens.

The material the dogs are made of wears out in a few months of use.

I buy 4 packages of them at once, every few years.

Pull off the inner cap, unscrew the bolt, remove the old cogs, put in the new ones, reverse the disassembly process and away we go.

Took off softner dispenser, took off bolt cover. Used 7/16 socket with long extension and unscrewed bolt. Pulled up on agitator and out it came. Took out directional cogs and replaced with new. Reversed procedure and I was done. Saved a lot of money by not calling a mobile repair man on this one!

Removed fabric softener dispenser. Inserted screwdriver into slot on side of cover that is on agitator and pried off. Used socket extension to unscrew bolt inside agitator. Lifted out and slid off plastic ring holding agitator cogs . Replaced cogs in the same direction they came out. Since these instructions were here on site at the time I ordered the parts, it made the job very simple and fast...the order came very fast too.

Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.

Sincerely,

Ken Lancaster

I removed the center cap from the agitator, which then exposed an inner cap with rubber seal. These were both easily removed with no tools... just a slight pull. Then the center screw was exposed. I removed that "one" screw and pulled the upper agitator assembly off. The old dog ears literally fell right out. I simply ensured that I placed the new dog ears in the same direction as the old, which is not hard to remember because the little housing piece that holds them is molded in the angle of the ears. Putting it back in took the most time because the new ears can easily fall out. In order to overcome this I had to assemble the pieces that had been removed and carefully put them back in place. At that point I had to manage to get the screw back into position and tighten it up. I put the inner cap with seal back in place and then the agitator cap... Done! It's an old machine but works great with a simple repair. The dog ears were so inexpensive that I purchased two sets. Great site!

Took the cap off the agitator, loosened the nut with a wrench, and pulled the agitator out. The agitator pulled apart easily, revealing the piece containing the dog ears, which were clearly worn out. Simply replaced the dog ears and reinstalled the agitator. Piece of cake!

I just took the bolt out of the top of the agitator which allowed me to pull the agitator straight up. Then I turned it over so the sleeve that the cogs go into could fall out. I took the old cogs out, put the new cogs in, held it upside down and lowered the agitator down onto as to not move the cogs. When it was all situated correctly I held it by the bolt as I turned it upright. Then I just lowered it back down in place inside the drum and tightened the bolt back down. Done.
The washer works just like new.