WFW96HEAC0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Isaac from SAN ANTONIO, TX
- Parts Used:
- WPW10208415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Se rompió la bisagra
Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from CATONSVILLE, MD
- Parts Used:
- WPW10448876
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The washer level switch broke
I am still waiting for the correct part to arrive, I was sent a part but it was the wrong part, the wrong part number and it was nothing that would work on a washing machine. I think someone else ended up with my part and I got theirs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from VIRGINIA BCH, VA
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn L. from CLAYTON, NY
- Parts Used:
- WPW10467168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer leaking
Followed internet instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Pine Island, TX
- Parts Used:
- WPW10352973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem
I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindie from DUNMORE, PA
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable), Wrench set
Front legs were rotted.
Replace front legs. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from TULSA, OK
- Parts Used:
- WPW10352973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not fill
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from PLEASANT PR, WI
- Parts Used:
- W11178521
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Countertop Dishwasher - Non Whirlpool
Since I have All Whirlpool appliances in the home, the only one not a Whirlpool was a counter top dishwasher that looks exactly like it could be a Whirlpool and so not to be the odd unit out, I labeled it with with a Whirlpool logo nameplate on the face of the door. Now everything matches perfectly and all in the same exact color white too.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Just measured and marked where the plate was to be located, cleaned that part of the surface, peeled the backing and carefully placed the logo name plate in place and pressed it on. Voila. Done and looks original as well. Call me the big, deep fakearooski.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from JONES, OK
- Parts Used:
- W11218344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced a worn out door bellows
I took the machine top off, then removed the control panel, removed old wire ring clamps. Removed door, removed inner clamp, water inlet tube, and bellows. Lubed up the new bellows with food grade silicone. Replaced the water inlet, inner clamp, door, outer spring clamp, reassembled the washer body and control panel and then ate a pizza.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LORAIN, OH
- Parts Used:
- WPW10467168
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replace tub to pimp hose.
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from OZONE PARK, NY
- Parts Used:
- WPW10208415
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken hinge on door
Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.
No more then 1 hour to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Lennon, MI
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bought a washer without front leveling feet
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David D from Severn, MD
- Parts Used:
- WPW10488048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Strike on Washer Door - prevented door from latching, and washer would not start
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Ardmore, AL
- Parts Used:
- W10763470
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had to install shipping bolts so we could move the washer
Really was not a repair
Was this instruction helpful to you?
Thank you for voting!