7MWTW1725BM0 Whirlpool Washer - Instructions

Spin indicator light was illuminated but machine was repeating rinse cycle rather than spinning water out of clothes. Replaced the pulley and drive coupler, thinking there was a mechanical problem. Video instructions were great but old pulley and drive coupler looked perfect so replacing them did nothing. Next I replaced the washer actuator (shifter), thinking that was the reason for no high speed spin. Easy job, as shown in the video, but it also did nothing. The problem turned out to be a failure in the control panel, probably resulting from years of vibration. Decided to stop chasing my tail and bought a new washer.

Fabric softener dispenser simply lifts off the top of the agitator. Then, a flat head screwdriver, tucked anywhere under the edge of the cap, lifts/pries it off. Then drop a 1/2" drive extension(no socket as it simply is the extension itself) into the plastic "nut" and remove it while holding onto bottom of agitator with your other hand. Lift it out, replace the cogs and reverse for reassembly. Total time less than 5 minutes, including shipping was $10.50 for cogs - repair #4 completed thanks to the fine folks at PartSelect! PS - part arrived at my door less than 24 hrs after ordering it even tho I requested 2-3 day shipping.

After a quick Google search I determined how to pull off the softener dispenser and top cover. Removed one bolt and pulled agitator out and apart.. Anyone who has used a socket set can do it.

Repair was simple and quick. Started by removing softener cup and removed bolt holding part that housed dogs. Removed housing and slipped of hold down clamp and replaced the 4 dogs then reversed procedure all took about 8 mins

Pop the top off the agitator, remove the bolt, pull off the agitator, pull out the part holding the cogs (dog ears),remove and replace cogs, reassemble. Works great now.

from start to finish was about 10 minutes. used screwdriver to pop off top cap of agitator. used ratchet with small extension to take out bolt for agitator. removed agitator, placed it on ground for leverage and pulled off top agitator. carefully observed old directional cogs. flipped top agitator upside down removed old worn out/ broken plastic cogs. replaced them with the new ones. hard to screw up they only install one way. kept top agitator upside down and put rest of agitator back on. flipped it right side up and pressed down hard for secure fit. placed agitator back in washer. reinstalled bolt. placed cap back on and was finished...25 year old washer working like new. $2.80 not including shipping...

I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.

Go to youtube and watch how to repair washing machine agitator. It is so easy. did the repair. Now it works, less than $20.00 to fix. Now I don't need to buy a new washing machine. Maybe it will make it another 15 years.....

The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Most of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina

After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agitator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!

repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.

We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.

Removed the four worn agitator directional cogs and replaced them with new ones

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

Followed youtube video. Great instruction.