WFW94HEXW0 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- william from VIRGINIA BCH, VA
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LORAIN, OH
- Parts Used:
- WPW10467168
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replace tub to pimp hose.
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Pine Island, TX
- Parts Used:
- WPW10352973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem
I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from MILFORD, MI
- Parts Used:
- W11415987
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Plastic shock slide broken
Unplugged the unit and remove the back cover of the washer. Broken shock was the right rear one so easy access.
Used channel locks to twist the upper and lower portion of the shocks to unlock them from the washer.
Installing the new part, it is advisable to clean the washer base cover that the shock fits into. Corrosion can make it difficult to insert shock tab and twist if not cleaned. I had to use the channel locks to twist, but be careful as the locking tabs are plastic.
It is also advisable that when you have the back cover off, that you clean the washer filter.
Used channel locks to twist the upper and lower portion of the shocks to unlock them from the washer.
Installing the new part, it is advisable to clean the washer base cover that the shock fits into. Corrosion can make it difficult to insert shock tab and twist if not cleaned. I had to use the channel locks to twist, but be careful as the locking tabs are plastic.
It is also advisable that when you have the back cover off, that you clean the washer filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from TULSA, OK
- Parts Used:
- WPW10352973
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Washer would not fill
replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from OZONE PARK, NY
- Parts Used:
- WPW10208415
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken hinge on door
Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.
No more then 1 hour to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Spring Lake, MI
- Parts Used:
- W11106747
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water leaking on floor from door
Watched this video on the website and went to work. Went very easy and smooth with removing the door. A pair of pliers works fine for outer ring. Kind of challenging by yourself, but I got it on in less than 5 minutes. Pliers in one hand and flat head screwdriver in the other to work the ring on. Much cheaper than paying someone to do it. 2 out of 10 for difficulty.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Ardmore, AL
- Parts Used:
- W10763470
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had to install shipping bolts so we could move the washer
Really was not a repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salt Lick, KY
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer posting a f6 error
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzie from Naples, FL
- Parts Used:
- W10839403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the front panel of the soap dispenser broke away
just clipped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Rock Hill, SC
- Parts Used:
- WPW10121596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Divider Broke
I just put the divider in the dispencer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Great Mills, MD
- Parts Used:
- WPW10289387
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Sediment clogging valve - E01F08 error code
Shut off water and disconnect hot and cold hoses. Use nut driver to remove three screws at back/top of washer. Slide top of washer back and up to remove. Use pliers to loosen band clamp on rubber hose and pull away from valve assembly. With fingers, disconnect wiring from hot and cold solenoids. Use allen wrench to remove valve assembly from frame of washer. Use reverse order to install replacement valve, although you can leave the top off the washer until you've checked for leaks.
Was this instruction helpful to you?
Thank you for voting!