WFW9300VU03 Whirlpool Washer - Instructions

Disconnect the hot and cold water supply hoses from the rear of the machine. Remove 3 screws in the rear that fasten the top cover. Slide the cover rearward and remove it. Disconnect the black outlet hose and unsnap the two electrical connectors from the water valve. Remove one screw that fastens the water valve to the rear panel. Slide the water valve away from the screw and remove it. Reverse this procedure to install the new valve.

Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Greatest difficulty was positioning machine to get at rear. Disconnected inlet hoses. Removed rear 3 screws to remove cabinet top. Removed rear holding screw to inlet valve. Removed two electrical connections to inlet valve. Disconnected inlet valve from interior hose. Reversed process to install new inlet valve.

Replaced water pump

Disconnected power. Turned of the water supply. Removed/disconnected the water lines from the washer. Removed the top by removing three screws. Disconnected the wires/connectors from the valve assembly. Disconnected the water line from the valve assembly to the dispenser assembly. Removed the screw holding the valve assembly on. Installed the valve assembly and reversed the above procedure.

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.

Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

open the front bottom panel (3) screws. remove panel. twist off old shocks by turning the shock counter clockwise. reinstall shock by turning clockwise.

I unscrewed the three small sheet-metal screws holding the washer top to the frame and slid the top aft and laid it on the floor. Then I took fine sandpaper and cleaned the plug contacts from the various components connected to the main control board. After five years or so I have found that most copper connectors will corrode and prevent electricity from flowing properly. That did not correct the problem. I checked the flow control device and it appeared clear and not binding. Then I pulled the drain pump filter and it was clear. I could hear the water pump running and the water flowing out the normal rubber hose. But the washer would stop three or four times during a wash cycle. Pressing 'RESET" and "START" would start the washer again. At the end of the cycle my wife noticed there was water in the washer tub. It had to come in via the water control valve. This is the valve you screw the hot and cold water hose into. It is a ice blue color and held in by one screw. I unscrewed the two hoses and removed the one screw. Then I had to slip the black supply hose from the valve leading to the flow meter. I disconnected the four electrical connectors and installed the new valve and found the screw hole did not align with the screw hole in the washer frame. I used a eighth-inch metal drill and drilled a new hole which lengthened the slot that the mounting screw normally went through. After I re-connected the hot and cold water lines to the valve I turned the water back on and put the top back on the washer. The washer worked like new. No stops. I did notice before changing the valve the water would flow into the washer tub like beer coming from a tap. After installing the new valve the water flowed in at three times the rate like a garden hose.

The repair was easy. It took 15-20 min to replace the valve at the most. Three screws on the back and the top comes off. The valve is right there on top. Undid water hoses and then one screw and one clamp to remove the valve. So simple and problem resolved. I also took this opportunity to replace the water hoses (they were over 7 years old) since I had to take them off anyway.

Replaced pump assembly

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

Followed video clip that I found online