WTW8200YW0 Whirlpool Washer - Instructions

followed video instruction that came with part. Previously watched youtube video (there are several, the low production videos are well worth viewing over the professional types). It was a breeze, other than the videos saying one person could do all four. When you get to the last rod, it is more difficult to lift the tub to insert the final rod in the round holder. I asked my wife for assistance.

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

This was the second time I did this repair, so it looks like this mechanism lasts about 3 years. I found the video instructions on your website very helpful, with one major exception. On my Maytag Bravos XL machine, there are no clips on the front of the top plate to release by pushing in a putty knife. Rather, there are two vertical brackets on the back of the top plate that are loosened or removed, and then the top can be slid forward about an inch and lifted up.

Also, the tiny electrical connection plugs are secured by plastic clips on the sides of the receptacles. Those clips just need to be spread apart a little in order to unplug the connectors; i.e., don't pull too hard on those plugs, or look for a release lever on the plugs themselves.

Repair is straight-forward. Thanks!

Exactly like the video from the website

This washer would not go into spin cycle without going out of balance no matter how we arranged the contents in the drum. We were looking to buy a front loader when I happened open this company with video instructions and positive comments from other people with the same issue. For the cost it was worth a try. Following the video and in less than one hour the washer was back in service. It now operates like the day we installed it new. Highly recommend this fix which should save you hundreds on a new washer.

Replaced the suspension rods

Followed video on your web site, and used that for ways to fix, good directions. If I was more organized it prob would of taken about an hour or less

The video posted on this site will walk you right through the repair. Great service. Thanks!

The washer would enter the spin cycle, but after starting to spin, would quit, and beep repeatedly. The fault code shown was DL. The manual cited DL as Door Lock malfunction. A check of the door lock switch suggested an internal problem. Sears offered the part at a far greater price, and shipping was several times more than PartSelect.com. PartSelect was chosen, and the part ordered on-line. Within two days the part arrived. Installation was simply a matter of lifting the top of the unit on which the door is supported. IT is done by inserting a narrow screwdriver into the separation, and pressing on the two metal springs holding the top in place. The old part was simple to remove by extracting two phillips head screws and removing the cable from the cable mounts underneath the top surface then threading the cable and plug back through the cable hole. Before that could be completed, the rear cover of the control panel was also removed, and after the plug of the defective switch was removed, the new cable was connected, and threaded back through in the reverse of the removal of the old switch, the phillips head screws, the control panel rear cover and returning the unit top to the resting position and snappin it into place. The Power ON check indicated that the problem fault code was cleared. The unit functions normally with the new switch. Hats off to PartSelect. The part was available in stock, and shipped promptly, and at substantially less cost than Sears.

Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!

I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.

It is good to watch a video on how to!
Most went well, like all repairs, there are surprises, that make It take longer than expected. Once I put it back together and ran it, there was a UL code. After reading more posts, I found UL is unbalanced. After reading more… one of the problems could be the hub on the bottom may be loose. I checked that. Yep the hex bolt was loose. I forgot to put lock tight on it. Fixed that and ran it, worked flawlessly.
It would be nice to have install instructions in the box. Otherwise watch videos.

Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you