WTW7800XW0 Whirlpool Washer - Instructions

Have the Maytag washing machine little over2 years and the water pump cracked - very disappointed.
Anyway, removed the back panel, unhooked the hoses, used 5/16 wrench to loosen up the screws, unplugged the power connector than replaced it with a new water pump.

It was an easy repair that I taught my 18 yrs old.

This is an easy one. Snap off the agitator cap with a screwdriver.
Remove the single but and agitator.
Remove 6 phillips head screws.
Lubricate the bearing and coax it off the spindle.

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

This was the second time I did this repair, so it looks like this mechanism lasts about 3 years. I found the video instructions on your website very helpful, with one major exception. On my Maytag Bravos XL machine, there are no clips on the front of the top plate to release by pushing in a putty knife. Rather, there are two vertical brackets on the back of the top plate that are loosened or removed, and then the top can be slid forward about an inch and lifted up.

Also, the tiny electrical connection plugs are secured by plastic clips on the sides of the receptacles. Those clips just need to be spread apart a little in order to unplug the connectors; i.e., don't pull too hard on those plugs, or look for a release lever on the plugs themselves.

Repair is straight-forward. Thanks!

Follow step by step YouTube channel for this.

Replaced each hose. Did discover that either hose can be used for hot or cold water lines. No longer required to label hot and cold replacement hoses.

I got the three rubber elbows to quickly (at an additional price). They were the correct part and fit exactly. I replaced the aggravating spring clamps with new radiator-type screw clamps which made the job easier and in my opinion better. Then I devised a little hardware cloth "fence" around the bottom to the washer to keep the rat out. The job is tough enough in that you must tip the washer forward to get at the lower elbows. Also probably a good idea to adjust the feet "in" as far as possible to minimize rodent access from the bottom.

The most difficult was to lift the top up. Releasing the clips was tough to push in and it broke some porcelain. The 3 screws on the plastic instrument cover was all that was required. Track the wires and remove the plug in and pull the wires through the access hole and misc clips, a Phillips screw driver removes the plastic switch .Simply place the new switch under the lid and the worst is done. Once the lid was up, 10 minutes and your done.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Used shop vac to remove as much water as possible. Turned washing machine on side to access pump. Removed old pump. Installed new pump. Used nutdriver to attach three fasteners and pliers to attach clamps to hoses.

Follow the video instructions.
No brainer..

The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.

By the way, it didn’t solve the problem.

Paul

1st watch a video on replacement of this pump.
My main issue was the guard I had to install and the correct way to
put it in. I know I got it right.
The pump is very noisy, loud!
It pumps out just fine.
Want to know if this is normal, Loud pump.
Let me know.
Thanks, Dave

The washer would enter the spin cycle, but after starting to spin, would quit, and beep repeatedly. The fault code shown was DL. The manual cited DL as Door Lock malfunction. A check of the door lock switch suggested an internal problem. Sears offered the part at a far greater price, and shipping was several times more than PartSelect.com. PartSelect was chosen, and the part ordered on-line. Within two days the part arrived. Installation was simply a matter of lifting the top of the unit on which the door is supported. IT is done by inserting a narrow screwdriver into the separation, and pressing on the two metal springs holding the top in place. The old part was simple to remove by extracting two phillips head screws and removing the cable from the cable mounts underneath the top surface then threading the cable and plug back through the cable hole. Before that could be completed, the rear cover of the control panel was also removed, and after the plug of the defective switch was removed, the new cable was connected, and threaded back through in the reverse of the removal of the old switch, the phillips head screws, the control panel rear cover and returning the unit top to the resting position and snappin it into place. The Power ON check indicated that the problem fault code was cleared. The unit functions normally with the new switch. Hats off to PartSelect. The part was available in stock, and shipped promptly, and at substantially less cost than Sears.

Just pulled the old water pump off and replaced with new one and was good to go. Thank you so much for sharing the problems and how to fix. Dean