Models > WFW9600TA02 > Instructions

WFW9600TA02 Whirlpool Washer - Instructions

Jump to:

All Instructions for the WFW9600TA02
106 - 120 of 169
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
James from Hopewell, NJ
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Front Bellow Moldy
Followed video, slowly. Was easier then I expected. Everything fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Houston, PA
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Washer fails to drain water
First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Troy, MI
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Water smells bad if washer sits for a few days.
I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tracey from Salem, OR
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Drain pump wasnt working
Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Billie from Dixie, WV
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Wasn't draining
Washed three loads and it was ok but then it stopped draining again. I don't know what to do.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Chino HIlls, CA
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Bellow torn at bottom - significant water leak
Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
Customer:
noemi from lakewood, NJ
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Bellow ripped
Followed video clip that I found online
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Reno, NV
Parts Used:
WPW10250553, WPW10003250, 8181731
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
My washing machine started leaking.
My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you
Was this instruction helpful to you?
Thank you for voting!
Customer:
donald from Stanwood, WA
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Socket set
torn bellow
repair was a cake-walk with the video there to help.Thanx
Was this instruction helpful to you?
Thank you for voting!
Customer:
turbo trucking from mio, MI
Parts Used:
280187
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Won't spin
Replaced water pump
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Chesterfield, VA
Parts Used:
WP8182210, WP8182119
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Socket set
Bellows stained
I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from North Pole, AK
Parts Used:
WP8182210, WP8182119
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Bellow had a large hole in it, and was letting water drain out all over the floor.
It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Katherine from Ridge, NY
Parts Used:
280187
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
My washing machine was not draining
I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from Dayton, OH
Parts Used:
280187
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
pump wouldnt drain
removed three screens on lower front panel removed hoses from pump after opening drain/filter to remove water slid pump forward and out unplugged pump wiring harness reverse to install
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from Rock Hill, SC
Parts Used:
WPW10121596
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Divider Broke
I just put the divider in the dispencer
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WFW9600TA02
106 - 120 of 169