WFW9400SU02 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gopaul from Queens, NY
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Bellow was damaged,water leakage.
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Avis from Abingdon,, VA
- Parts Used:
- WPW10156617
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic retainer ears broke
Took old broken part off and replaced with new. Involved removing 2 screws and putting back.easy repair. Biggest problem was length of time it took part to arrive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Douglas, AL
- Parts Used:
- WP8182119
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace Bellows between door and tub
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 people
connect bellows to door with spring clip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AUSTIN, TX
- Parts Used:
- WP8182862
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disconnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from JACKSONVILLE, FL
- Parts Used:
- WP8183202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken hinge
Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude van from big sandy, TN
- Parts Used:
- WPW10388414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
tub would not turn
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from YARDLEY, PA
- Parts Used:
- WPW10110225, WP8182862
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Inlet valve was stuck in open position allowing washer to fill with water when not in use.
Removed lid. Took old parts off and replaced with new parts. Also replaced hoses while washer was moved away from wall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francisco from DELTONA, FL
- Parts Used:
- WP8182862
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Tub filling when power was off due to inlet valve leak.
Followed instructions as shown on repair video at site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Lady Lake, FL
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Pump not working
Replaced pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from ROCHESTER HLS, MI
- Parts Used:
- WPW10250572
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The part was made wrong and did not fit.
The plastic tabs were too large to fit into the washer's slotted hole in the washer cage. I initially bought this part from a PartSelect competitor and it was made wrong as well. Whirlpool themselves showed this part on back order so the faulty part originated in a Whirlpool order to a vendor. The reason for this reply is that PartSelect resolved this bad part issue within 2 hours and 1 phone call. The competitor has not resolved anything yet in 3 weeks and 5 emails with image proof.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from EASTPOINTE, MI
- Parts Used:
- WPW10003250
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.
I replaced the hose and reinstalled the panels and I was done.
I replaced the hose and reinstalled the panels and I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evette from Mayfield, NY
- Parts Used:
- 280187
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
the pump wasnt puping out the water
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this instruction helpful to you?
Thank you for voting!
Torn bellow lip
Replace bellow with help from Youtube video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn L. from CLAYTON, NY
- Parts Used:
- WPW10467168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer leaking
Followed internet instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Gary, TX
- Parts Used:
- 280187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Was this instruction helpful to you?
Thank you for voting!