WFW9300VU02 Whirlpool Washer - Instructions

I found a you tube video with step by step instructions. Very easy to follow. Repair would have been quicker had my kids not been at home. I had to have my boyfriend help me put on the outer bellow spring clamp, as I was not strong enough. Washer works great.

Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

To verify it was the motor making the noise not the drum bearing I removed the belt and rotated both by hand to see which one made naoise - then I ordered the motor.
To install the motor remove rear panel, slip belt off, remove 1 bolt holding motor in, carefully slide motor towards you until pivits disengage. Wires are ling enough to set motor on bottom of washer and rotate for easier access to connector. Install motor in reverse sequence.

First I took the top, front, and back off of the washer. There were about a gazillion wires and tubes so I went slow and took pictures. I had to get the old tub out so that I could replace its back half. The new outer tub contained the replacement bearing. Taking the tub out took about two hours because I went slow so that I could document the process. Once the tub was out, I split the tub in half and found a real mess of a bearing. I couldn't get the old bearing race off of the shaft, so I went to the store to get some sand paper. With sand paper I was able to smooth the shaft down enough to get the old race off. The inner tub and the outer rear tub went together pretty easy with a couple swats with a hammer. Putting the clips back on was a trick. My oldest son figured it out. This was actually a family event. I am the father of ten children so you can imagine how important a washing machine is. After another couple of hours, we had all of the wires attached and the hoses hooked up. There is a metal band that holds the plastic shroud in the front to the outer tub. It took my daughter-in-laws long piano fingers to get that put on right. When we had it working finally, the bottom drain hose was leaking. The little clamp that came with the machine wasn't doing its job. Then the metal band came back off. Well, I went back to the store and bought a 10 inch metal band clamp for the bottom hose. That did the trick. I tightened the big band real tight and everything is wonderful. My wife is happy again! No more trips to wash clothes! I saved some money and some time and it wasn't that bad.

1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remove 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.

1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

It took a few minutes to realize that the part slide into place instead of snapping in. In order to get the part to slide into place i put my head in the washer to hold the drum in place then with both hands slide the part into place.

I followed the repair blog by the poster most liked...

Somehow a bobby pin got into the drain pump housing. When it started to drain, the pin was rammed through the housing.Extremely easy to remove and replace. No special skills needed. Whirlpool did a good job in making it idiot proof. Unpacking the part took longer than installing it. Don't be afraid to do this repair. If you own a pair of pliers and a screwdriver,you can do it.

Disconnected 2 hoses and 1 screw and remove3d the old pump and reversed the proceedure to install the new pump.A piece of cake. Thanks

I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.

I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

After removing the Top Cover and back cover by removing the 3 screws for the top and 10 screws on the back cover to expose the interior of the machine. Remove the rubber hose that was attached to the bottom of pressure switch. Pushed gently upward on the pressure switch until it popped out. Gently press down on the 2 small tabs on the plug and then gently pull the plug out. Placed new pressure switch in place, plugged the connector back into the switch. Also doubled checked the hose to ensure that the tubing has not rubbed a hole it from rubbing on the concrete counter balance. If yes then remove the tube from the bottom of the washer and replace with approximately 2 feet of 3/16 inner diameter/1/4 outer diameter tubing. Attach the new tubing to the bottom of the washer port and the pressure switch. Attach the new tub to the water discharge hose using tie wraps or electrical tape to ensure not to occur again.

First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

slid new baffle into place. No directions with new part, fortunately it was easy to figure out how baffle locked into place.