WFW9700VA00 Whirlpool Washer - Instructions

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

There is a video on this site that shows how to do the install. It is perfect and accurate. This pump is one of the easiest components to fix on this washer and it will save you money to do it yourself. Tech has told me twice to buy a new washer. This did the job. Make sure to take the time to fully drain the machine prior to doing this and make sure that you unplug your machine. To drain, just unscrew the cover on the front of the pump. If you start disconnecting hoses without draining you could have a mess on your hands depending on how much water is still in the washer. Use a shallow pan or bucket if your machine is on a pedestal. I have a floor drain in front of mine so I use a piece of foil to channel the water into it. After that, just do the install like the video. Also make sure to examine the reconnected hoses after you get done to make sure that they are solidly attached to the pump and that the base of the pump is tightly secured to the bottom of the machine. You have to secure the feet of the pump from the bottom which is why the video recommends putting blocks under the washer to have access to the bottom. Pump is great. Everything works well.

Son-in law did the work he was finished in about 20 minutes the repair guy wanted $249.00 to take out and put in. PLUS part.

I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

Unplugged washer , used shop vac to drain water through drain hose on washer. Removed both hoses from old pump. Removed electric plug, removed 2 screws from bottom of the pump. Then reverse the process.

Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!

We do not wish to have our repair published. The part itself was perfect and corrected our leaking problem but we did have difficulty with the installation despite detailed instructions. We appreciate a good price for the perfect part!

I followed the directions as given in a video from this site, and it was pretty simple. It can be done without power tools, although I used screw driver heads on a drill. The only iffy part was that some of the star-shaped screw heads were shallow and I had to be careful not to strip them. In brief, the fix required removing the door from the machine, unscrewing the inside of the door from the outside, removing the broken hinge, inserting the new hinge, re-aligning the inside and outside of door, screwing it back together, and re-attaching to the machine.

replaced actuator switch. It did not fix the problem. Replaced actuator arm, and fixed. Needed the switch because gears were stripped. Needed the arm because it seems over time, the arm straightened, thereby increasing its length so that the rotation of the switch bound up during its cycle.

Had difficulty getting the door off the washer because I didn't realize there were two hooks in addition to the two screws that held the door to the washer. I reviewed the repair video several times through out the repair. Probably unscrewed more than I needed. Got the new hinge installed on the door. The problem was I couldn't hold the door at the right angle to get the hooks inserted. The washer is near the wall so I couldn't open it all the way and bending over at an odd angle didn't help. At nearly 80 I don't have the strength I used to!! After trying and with the door falling on my arm I gave up and called a friend. We did have difficulty getting the hooks inserted correctly. I held the door and she got the hooks in. On the good side, the hinge part fit like it should!!