WFW95HEXW2 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- GARY from CLARKSVILLE, IN
- Parts Used:
- WPW10110225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
F-20 Error Code
Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from JUPITER, FL
- Parts Used:
- W11266654
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It took two of us to hold the ring and slide it on around the opening with the assistance of screwdrivers the spring was very tight
Two people to screwdrivers, stretching the spring out and around and that’s the last part to go on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from NASHUA, NH
- Parts Used:
- WP89503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from JONES, OK
- Parts Used:
- W11218344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Replaced a worn out door bellows
I took the machine top off, then removed the control panel, removed old wire ring clamps. Removed door, removed inner clamp, water inlet tube, and bellows. Lubed up the new bellows with food grade silicone. Replaced the water inlet, inner clamp, door, outer spring clamp, reassembled the washer body and control panel and then ate a pizza.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David D from Severn, MD
- Parts Used:
- WPW10488048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Strike on Washer Door - prevented door from latching, and washer would not start
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out - it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn L. from CLAYTON, NY
- Parts Used:
- WPW10467168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer leaking
Followed internet instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Isaac from SAN ANTONIO, TX
- Parts Used:
- WPW10208415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Se rompió la bisagra
Desarme la puerta y coloque la nueva con mucha facilidad, nunca reparé un electrodoméstico antes de este, seguí el diagrama que encontré en el sitio para elegir la pieza que se rompio
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from LORAIN, OH
- Parts Used:
- WPW10467168
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replace tub to pimp hose.
Factory hose clamps were awkward to maneuver. I used automotive radiator hose clamps instead. They worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from VIRGINIA BCH, VA
- Parts Used:
- WPW10467289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Replacing the heat sensor following an F-24 Error Notice.
I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from North Augusta, SC
- Parts Used:
- WPW10312527
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Washer failed to fill and run wash cycle. Internet research quickly provided clear problem definition and solution.
Removed top cover. Unplugged switch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Pine Island, TX
- Parts Used:
- WPW10352973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem
I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindie from DUNMORE, PA
- Parts Used:
- WPW10001130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable), Wrench set
Front legs were rotted.
Replace front legs. Very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Greenacres, FL
- Parts Used:
- WPW10247306
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer kept filling up with water after the load was completed because the valve was leaking
Checked YouTube and the guy walked me through the process and it was exactly as he described
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tonawanda, NY
- Parts Used:
- WP8183270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Door would not lock
Did the repair just like the video on your website. Was really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from MILFORD, MI
- Parts Used:
- W11415987
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Plastic shock slide broken
Unplugged the unit and remove the back cover of the washer. Broken shock was the right rear one so easy access.
Used channel locks to twist the upper and lower portion of the shocks to unlock them from the washer.
Installing the new part, it is advisable to clean the washer base cover that the shock fits into. Corrosion can make it difficult to insert shock tab and twist if not cleaned. I had to use the channel locks to twist, but be careful as the locking tabs are plastic.
It is also advisable that when you have the back cover off, that you clean the washer filter.
Used channel locks to twist the upper and lower portion of the shocks to unlock them from the washer.
Installing the new part, it is advisable to clean the washer base cover that the shock fits into. Corrosion can make it difficult to insert shock tab and twist if not cleaned. I had to use the channel locks to twist, but be careful as the locking tabs are plastic.
It is also advisable that when you have the back cover off, that you clean the washer filter.
Was this instruction helpful to you?
Thank you for voting!