WFW9250WR01 Whirlpool Washer - Instructions

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

I watched the video and it really was as easy as it looks. Great shipping time, I ordered the pump Monday and it arrived on Thursday, standard ground shipping!

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

removed top,3 screws in back,lift up and pull back.removed soap dispenser.removed hidden torx screw on left side. removed screw top center of door opening,used putty knife to pop control panel off and laid on top of washer.used small screw driver to pop off front gasket spring and wire from left side.took gasket loose and remove door lock and let it hang there,took off kick panel and front then un screwed the inner gasket retainer,pulled off gasket.soaped up new gasket and reinsalled in reverse order..it took two of us to get the front spring and wire back on,that spring is tough and the gasket kept popping off,finaly got it,works fine

The key to this repair is 1) lifting the front of the washer to access the bottom trim bolts, and 2) using lubricating spray around the outer bellows clamp area and 2 people to work the clamp into place.

Turn off water and power. Pull top off first, then bottom front kick plate. Take all the screws out of the soap tray. Disconnect the front panel from the controller, then the upper front panel comes off, but be careful with it as it is plastic tabbed. Pull upper metal support brace off. Detach the door lock BEFORE you pull the door off (two torx screws). Take a flat head screwdriver and release the spring holding the bellows to the front door/panel, then fold bellows into washer a bit. Remove front door/panel. Back bellows clamp is Phillips, loosen and remove bellows. reverse steps to put back together, but run machine in rinse/spin with top and front lower kick panel off to make sure of no leaks. Also good time to check pump lint screen for junk in it too.

Took less than 5 minutes to replace, So Happy;-)

put in push down push back until they lock in

Removed top panel. Removed rear panel. Replaced belt. Fairly easy only issue was getting the actual belt pulled enough to wrap around the pulley.

It took a very long time to attempt to diagnose the problem with this type of washer, finally was able to get the diagnostic to run and it said it was the Motor Control Unit (MCU). After ordering the part which was easy, it was not the reasoning for the problem and I still cannot get this machine fixed. Returned the part with ease, just waiting for the refund to go through.

Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

Well first off the part is different then the orignal so it does not fit correctly. I removed the old bellow and its cicular spring clamps. On the new bellow there is not enough lip on the rubber for hte clamps to be put back on and hold the bellow in place so it still leaks out the door. if the part was a match it would work but since the part number was changed and the design was changed it now does not fit correctly. INstructions did not come withthe part so had to find them online.

the repair cost was about 1300$ from a repairman! and they wanted to replace the complete inside drum assembly, so i decided to break it down myself and i'm an average do it yourselfer 1. unplug machine 2. remove water hoses 3. remove the top 4. remove back panel and front complete 5. remove all inside connecting wires but leave them close as to make it easy to reconnect 6. take all three shocks loose from bottom of drum and remove all counter weights (concrete) 2 on front and 1 in back as to keed drum ballanced for removal and 7. remove the complete drum 8. set drum down door side down and remove pully and then all the metal clips with a flat screw driver and lift back portion of the outer drum up and remove. then the inner drum will be visable 9. take the 6 Torx (star) screws out of the drum support and remove! and semply reverse the process for assembly! taken photos of the process will help the assembly process as well

Removing and reassembling the front and top panels was very easy and straight forward. I started by opening the clean out next to the pump and to my surprise found 2 shiney pennies a rusted paper clip and a small nail. I inspected the bellows and found 2 - 1/4 inch slits near the drain holes in the bottom of the bellows, not big enough for the pennies to pass through so how did the pennies get there. Installing the clamp to the drum was fairly difficult. The hardest part of the bellow installation was getting the front spring clamp lined up and stretched. I used the old spring clamp, maybe a new one would halve been easier.I used some duct tape to hold the wire clamp in place and a screwdriver in one end of the spring and with a great deal of effort stretched the spring enough to get the clamp over the rim. I also sprayed some water on the groove in the bellow to get to seat on the rim