WFW8400TE00 Whirlpool Washer - Instructions

Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

I purchased the downloadable Maytag Maintenance Manual (PDF format) and followed some of the directions and pointers from this web site. All in all, it was a pretty simple process. 1) Take the top off - 3 metal screws, 2) take the control console and detergent dispenser out - 1 T-20 Torx screw and multiple plastic clips and 1 wire connector, 3) take the lower panel off - 3 metal screws, 4)take bellows retaining ring off -- spring retainer used a needle nose pliers, 4) take off door latching mechanism - 2 T-20 Torx screws and multiple clips + 3 wire connectors, 5) take front panel and door off - 4 metal screws, 6) remove bellows retaining clamp with phillips screw driver, 7) remove old bellows. Reverse the process to install new bellows. On installation, make sure that bellows drain holes are at the bottom of the door. Also, hardest and most time consuming part was installation of the metal retaining ring (spring retainer) fought with it for about a half hour before I finally got it on. BTW all metal screws for my machine were 1/4" head the remainder were all Torx T-20. Good luck!

After getting dress that wife denies closing in door out the repair wasant to hard. There are 3 or 4 phillips screws in back that holds top on that have to be taken out and the kick plate cover on bottom just snaps off but the rest is covered very well by other discriptions.(by the way the dress had to be thrown away so not only did i get to by bellow but a new dress also and the bellow was cheaper)

Just follow the repair video and you are good to go. Very easy my 16yr old did it.

I watched the youtube video, then ordered the part from partselect. I then took my ipad out to the garage where I placed my washing machine and completed the removal of the old seal and installed the new one with ease. Be patient when you try and fit the new seal over the lip on the machines doorway. That was the only hard part. Once I got it started, the rest was easy. I am very happy the video was available and even easier to follow the link to order the part. Thanks! Presslerc

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!

I found a YouTube video that showed how to totally dismantle the machine. I removed the top ( easy 3 screws). Removed the bottom access panel (easy). Removed the control panel (1 Torx screw and rather tricky to unsnap). Removed the door and hinge (2 Torx screws). Removed the below retaining band (easy). Disconnected the bellow at the front panel then removed the door lock mechanism (easy). Removed the front panel (easy). Removed the bellow clamp on basket side (screwdriver hose clamp type, a little tricky but not too bad). Installed the new bellow paying close attention to the drain holes being centered on the bottom. Assembled all parts in reverse order. The really tricky part was the bellow clamp on the front panel. Patients prevailed.

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

Took less than 5 minutes to replace, So Happy;-)

put in push down push back until they lock in

Well first of all when you buy this washer, the salesperson should tell you about checking the drain catch (ahead of the pump) and emptying out whatever get's caught in there. Never had a clue until it wouldn't work, then did a search on the internet, and darn if I didn't find specific instructions on how to open and clean out. Mine was packed full of hair pins, small change, lint, buttons, etc, all kinds of stuff. Guessing that is why the pump went out in the first place, it was so packed full that the pump could not draw any water through. But even after I cleaned it out, the pump was already shot. So called a service man, he said the pump would cost me around $200, then his labor to put it in, plus a $68 service call to just come and look at it, and $68 when he comes back to replace it. So I searched the internet for how to replace, came up with a very detailed You Tube video on how to replace Whirlpool Duet Pump. So ordered my pump from PartsSelect, just over $100, and replaced it myself. Super easy, only about 5 minutes. Thanks! —A very determined housewife!

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

Replace water pump

The only issue I had was getting the hose from the tub re-installed, but that was my fault, the pump went right in. It couldn't have been easier. I was very pleased, received the replacement pump in just a couple of days, packaged very well for shipping, and had it installed in a matter of minutes. It took longer to take off front panel to access pump than it did to install it. Very pleased with "Part Select".....will use again!