7MWTW1709YM1 Whirlpool Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- carl from HUNTSVILLE, AL
- Parts Used:
- WP8578209
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Washer did not spin. Broken bolt inside agitator. Needed to replace agitator.
Part ordered was incorrect even though your website said that it was correct when I ordered it. Part sent back. Have since bought a new washer. Your contact person to return part was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eldon from Liberty Lake, WA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Top part of agitator quit agitating in one direction.
First, I removed the (3) piece softener cup from the top of the agitator.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Then I removed the bolt from inside the top of the agitator.
The agitator drive assembly lifts out of the lower agitator.
A flanged plastic snap ring holds the (4) drive dogs into the drive assembly.
Use a small screwdriver to remove the snap ring.
Replace the (4) drive dogs, and reassemble in reverse order.
As far as repairs go, this one is really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from OXLY, MO
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Banging when in spin cycle.
I FOLLOWED THE INSTRUCTIONS IN THE VIDEO AND HAD NO PROBLEMS. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luu from STANTON, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No problem
That OK , easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Corvallis, OR
- Parts Used:
- WPW10072840
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The cap thingy seal broke and splattered fabric softener.
I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Oldtown, MD
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Top portion of agitator not turning
The top portion of the agitator was not turning so that laundry could be drawn down in the wash tub. The problem was 4 little cogs that where worn and would not catch on a gear/cog portion of the bottom portion of the agitator. the cogs where about $10 delivered and it took about 25 min. to install (from top of washer). The old cogs, I also repaired by taking them out and using a hacksaw to redefine the grooves on them. They are still working, so I will hold on to the new parts until needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Wetumpka, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
worn our Agit-dogs, agitator wouldn't pull clothes down
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roger from Delanco, NJ
- Parts Used:
- WPW10072840, 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
upper agitator not spinning
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canandaigua, NY
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator stopped turning
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Little Rock, AR
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator would not agitate properly
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the agitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Lindenhurst, NY
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top partion of agitator turned in both directions by hand and was not driven by the motor.
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Depeturie from Madison, AL
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Top of Agitator would not rotate
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Penu from SAN MARCOS, CA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Washer agitator was slipping
Removed the agitator cap, then removed the plastic, spring loaded retaining part (needed a square head tool). Once out, the cog retainer came out, replaced all four cogs, and replaced in reverse. Easy as pie & took 10 minutes!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KISSIMMEE, FL
- Parts Used:
- W10780048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Washer drum banging on spin cycle
Very simple repair with the kit. Old rods came out easily using vise grips locked on to rods about 10-12 inches down and pulling up. Had doubts if they were bad since everything looked good but drum bounced back several times when I shoved it down to test it earlier. New rods went in just as easy and replaced in less than 30 min. Hardest part was that I had very cramped laundry room so had to move and disconnect hoses etc. to move into larger space for repair and then move back to reconnect. Parts came quickly within about 3 days and now purrs like a kitten!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrique from Miami Shores, FL
- Parts Used:
- WP21258
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
spin cycle did not activate
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.
Was this instruction helpful to you?
Thank you for voting!